A loosely moderated place to ask open-ended questions
Search asklemmy π
If your post meets the following criteria, it's welcome here!
Looking for support?
Looking for a community?
~Icon~ ~by~ ~@Double_[email protected]~
Okay I'll bite the bait. THE TOP ONEβ½β½β½ What sick form factor are you using with vertical VGA ports?
You need to rotate your pc case if the VGA port isnβt vertical. The ground pins always need to be on top so all those grounding electrons weigh down the other conductors to make the data flow more quickly.
That's not true. VGA is a horizontal spec with the entire trapezoid housing being the ground contact. The data electrons to one side is due to the earth's axial tilt spinning them into a corner via healing crystals.
Uh no, the ground pins need to be at the bottom so theyβre near the ground idiot
That's when you use the ports placed on the motherboard in a standard verical PC case, meaning the system uses integrated graphics for the visual output instead of deticated videocard. Videocards that are put into MB at 90Β° are horizontal, right, but in most office setups I handle they are rare nowadays. Videocards are almost exclusively installed when you handle 3d and content rendering in demanding apps, and for office and browser stuff they are too costy after the crypto price hike and in a sanctioned Russia.
Nettops have horizontal motherboards tho.
standard verical PC case
Excuse you! Standard PC cases are horizontal:
Desktop computers that have a vertically standing motherboard.
Many machines have vertical connectors, if the machine is turned for any reason. Or you're using the on-board card, etc.
Haven't plugged in a VGA cable in a long time. As someone else pointed out it depends if it is temporary or long term.. I always screw them in if it is long term
Haven't plugged in a VGA cable in a long time.
Exactly. What have you done to HDMI and DP ports?
DVI is the Gen X of video connectors
VGA is the Boomers and HDMI is the Millenials. Gen-Z is using USB-C.
Nobody likes DisplayPort
DisplayPort is the cool uncle who is happy to mind the kids for free. A lot of people copy his smooth relaxed style and mannerisms without realising.
I tighten both screws. With an impact driver. And a dab of LocTite for good measure.
Easy there, Satan!
Both every time but I also haven't used a VGA cable in at least 15 years.
Lucky you lmao
I still see them once every so often
In fact, I went onsite to a customer who wanted a new PC set up because the old one "wouldn't boot". Sure enough the cable was sticking out of the monitor at about a 15deg angle. I pushed the VGA cable in a bit extra hard and it came right back.
I was out of there in about 30min.
For quickly testing something: fuck screws.
For long-term use: both a tight as I can so I barely can unscrew them later because why not.
Long term use, at least one
Temporary, fuck the screws all together
And it was always temporary!
I've had less fall out than I had cases where the screw stuck in the socket and it started unscrewing out of the motherboard that I just gave up on them altogether
Jesus Christ, both!! π But only finger tight. Sod you bastards who get the screwdrivers out! That's overkill. π
Who does just one? That's worse than not doing either. Since they're captive screws, doing just one can force the connector to wedge in crooked. I've had issues with tightening one too far before starting the threads on the other. Sometimes you have to go back and forth a couple times
Both, heathens dont bother and they reap what they sow.
Hahaha, I can't disagree, even as a heathen.
As others have said, depends on how permanent something is
Pro tip: It's a lot easier f you twist both knobs at the same time using the same motion as opening a bottle cap.
I loathe when the stand offs come out with the vga cable!!!!!
Both
Hand tight, then torque wrench, 7-inch pounds.
Well that's retro but I used to only screw in the side that's easier to reach because that already secures it while also allowing you to more easily unplug it again.
Both. Lose cables are annoying.
A school computer lab with a bunch of grubby-handed students touching and licking and who knows what to every surface? Yes, VGA cables get screwed down.
If it's for more than a minute I'll screw in VGA and DVI cables
Both. If there's a screw, I'm tightening it, baby.
Both, three rotations after the threads catch.
One or none bears the risk of the connector coming out crooked and bending the pins, causing a potential alignment issue on the next connection and bending them further.
VGA cables? You mean grappling hooks?
When I used them, I screwed both in usually.
I've always screwed them both in very lightly
Neither. Trip hazard.
Lightly screw in one
And then replace my old shit and not touch anything but HDMI or DP for the last ten years.
I think this is highly dependent on the setup.. like is this temporary, semi- temporary, or permanent?
I sure wish my external HDDs had screw in ports. Those things come loose if there's a change in air pressure.
It depends.
For my work computer, I screw them in tight, both on the monitor and the DP/VGA adapter.
For stationary devices (like overhead projectors) and extension cords, I screw them in, but not very tight.
For classroom computers, I only screw them in on the monitor and leave them unscrewed on the computer. Students can't keep their legs calm and often snag the cables. I prefer to let the connectors harmlessly disconnect instead of damaging the graphics card or motherboard.
My current job, we test products with these cables, we are required to screw in both when plugging it in, so both.