this post was submitted on 27 Nov 2023
14 points (100.0% liked)

3DPrinting

15629 readers
641 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
j4k3
andypiper
henry_rowengartner
[email protected]
14
Constantly Adjusting Z Height Offset (self.3dprinting)
submitted 1 year ago by OZFive to c/3dprinting
9 comments fedilink hide all child comments
 

Good day! I am running a Klipperized Sovol SV06+ and have been getting some really great prints. I am however having an issue where lately I am having to adjust the Z offset with each new print. I did a first layer calibration and got a perfect result but after a couple prints I saw I needed to lower it to get a good first layer. Again I printed a few and then again I needed to lower it. This has happened a few times.

Yesterday I was printing a pretty large print and midway through the extruder shifted (the print remained secure to the bed) and continued printing. After I canceled the print I had to lower the Z offset much further than I thought was possible. I am concerned that the bed keeps "lowering".

I have a very good bed mesh loaded (used the silicone bed leveling mid I have seen discussed). I am just unsure why this is needing to be adjusted and why the last print went wonky (related?)

Thanks much!

top 9 comments
sorted by: hot top controversial new old
[–] Brainsploosh 4 points 1 year ago (1 children)

I have no experience with your particular printer, but I've had an issue where the bed was very sensitive due to being the edge of the adjustment range.

The bed screws on the Ultimaker 2 are manual screws with springs, and you can level the bed throughout most of the screw length. Having it at one end means the spring is quite loose, and things like weight and nozzle pressure affected the flatness of the bed.

So if you have an elastic tensioner for your bed, maybe set it at higher tension for a more robust flatness?

If you're always adjusting in the same direction though, it's not that, and is probably a software error where something doesn't count Z-position right. Unless of course your printer is somehow getting longer?

[–] OZFive 2 points 11 months ago

The printer bed is non adjustable. It relies solely on auto bed leveling. I did a silicone base mod to actually adjust the bed and level it manually in addition to the abl. That is why I had such a great mesh loaded.

[–] [email protected] 3 points 1 year ago (2 children)

How is the z position determined? Is it with the probe or a fixed endstop? Check that there's no play in those parts.

[–] OZFive 1 points 1 year ago

Probe, will check!

[–] OZFive 1 points 11 months ago

No play. The probe is secure and didn't move at all.

[–] [email protected] 2 points 1 year ago (1 children)

What type of material are you printing? Could be the material is eating away at the brass nozzle causing you to need to adjust the z offset.

[–] OZFive 1 points 1 year ago (1 children)

Overture PLA

[–] [email protected] 1 points 1 year ago (1 children)

Shouldnt be the filament then. I would make sure the probe is fully secured like the other comment suggested. Good luck, that sounds frustrating! I need to adjust mine, but usually after printing for a couple weeks.

[–] OZFive 1 points 11 months ago

It is secure. Not a wiggle or jiggle to it.