3DPrinting

15720 readers

117 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 2 years ago

MODERATORS

Any recommendations for a low-cost, low-hassle printer? (self.3dprinting)

submitted 3 weeks ago* (last edited 3 weeks ago) by CommissarVulpin to c/3dprinting

53 comments fedilink hide all child comments

Several years ago I leapt enthusiastically into the realm of 3D printing by buying a massive, expensive delta-type printer. I had to put it together myself, which was fun, but after that I struggled to get it to print well. Even simply trying to get the prints to stick to the bed were difficult, leading me to add huge brims to all my parts which were a pain to cut off afterward. Eventually I gave up fiddling with it and it’s been gathering dust ever since.

I know that a lot of you treat the hobby as an opportunity for endless tinkering and optimization, which is great, but I think I’ve realized that what I’d prefer is something that just works out of the box with a minimum of adjustment.

you are viewing a single comment's thread
view the rest of the comments

[–] [email protected] 5 points 3 weeks ago* (last edited 3 weeks ago) (2 children)

For good bed adhesion I think I have a couple pieces of advice:

Get a PEI bed if you don't already have one. It makes a world of difference.
If that doesn't stick well, consider getting something like this
Make damn sure your bed is level
Make sure the Z offset is properly set up
If you aren't already, start by printing PLA, then move on to other filaments once that goes well.
Make sure you have proper temperatures for both the hot end and the bed. Normal values for PLA are 210-230 on the hotend and 50-60 on the bed.

[–] CommissarVulpin 3 points 3 weeks ago (1 children)

Thanks for the advice. The model I got (SeeMeCNC RostockMax 3.2) has a stationary glass bed and this fancy system where it probes the bed and automatically makes a height map. I might end up trying to get a new bed surface like you suggested before springing for a whole new machine.

[–] IMALlama 1 points 3 weeks ago

You could buy a large PEI sheet in sticker form and put it directly on your glass bed. Removal with a razor shouldn't be difficult.

Is your bed heated? If yes, prints will stick well to the PEI when it's hot and pop off when it's cooled down. I have an ultrabase glass bed on my i3 clone and that's exactly how it works there. I also gave a similar experience with my Voron with a PEI coated spring steel bed.

If your bed is unheated you might still be in hard mode.

As a final thought, go hot and slow for you first layer. I usually bump my first layer by 5-10 °C, depending on the material, and print it at 30-40 mm/sec. Even though I could probably go faster I'll take consistently in my first layer.