this post was submitted on 18 Apr 2024
14 points (93.8% liked)

3DPrinting

15647 readers
375 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
14
submitted 7 months ago* (last edited 7 months ago) by papalonian to c/3dprinting
 

Hi everyone, I'm having constant clogging issues with my printer that sprung up out of nowhere. I'm running out of things to test.

The printer had been running several prints a day for several days when I decided to change nozzles for one print. Ever since then (~2 weeks ago) i have not completed a single print, due to clogging. I have tried:

Replacing the PTFE tubing in my hotend.

Replacing the nozzle. (I've used a handful of nozzles, all with the same results)

Trying different filament.

Replacing the hot end with an all metal hot end, trying three different heat breaks from two manufacturers.

Removing the printer from its enclosure to ensure proper cooling.

Adjusting extrusion tensioner.

All the other basic obvious stuff like making sure there's no blockages anywhere (whole hot end and nozzles have been soaked in acetone, torched, brushed etc).

The printer will seem to work fine for a little while before either slowly failing to extrude until it completely jams, or it completely jams all at once. I don't think it's heat creep, because I tried setting the nozzle to printing temp, letting it sit for half an hour or so and running filament through it and it had no issue, whereas prints usually start to fail within the first 10 minutes. It also doesn't have anything to do with my print settings because I'm able to get it to clog sometimes by just running the extrude command.

I'm completely at a loss here. I don't know what else to try. Does anyone have anywhere else for me to look?

Update: I tried detaching the heat block from the rest of the printer and running filament through the (cold) heat break, and it got clogged. There was a small bit of filament adhered to the inside of the heat break. So it's apparent that's where the clog is forming, it's just a matter of finding out why it's happening. Everything seems to point towards heat creep, but even when I intentionally try to heighten the conditions that to cause heat creep I can't intentionally replicate the clog. I'll keep experimenting down that route, though.

Update 2: After clearing that clog, I noticed the short piece of Bowden tube between the top of the heat break and the top of the heat sink was slightly too short. I modified the heat sink to bypass this short piece altogether; the Bowden tube now goes directly from the extruder into the heat sink to the top of the heat break. I also applied a thin layer of thermal paste to the outside of the heat break to ensure good contact/ heat transfer with the heat sink.

After doing all of this, I ran a PID tune and, with my AC set to lower than average, started extruding filament. After extruding ~300mm of filament, I tried a few nozzle and filament swaps using very careful techniques to avoid leaving any residue. I'm able to pull the filament out in a solid piece to where I can see light through the nozzle afterwards. Then, finally, out of the blue, the clicking returns. Another clog. I wasn't able to remove the filament as cleanly this time to inspect the clog, but I'm strongly suspecting heat creep at this point, despite going above and beyond to mitigate it. It's quite late though and I've got work tomorrow so it'll have to wait until then.

you are viewing a single comment's thread
view the rest of the comments
[–] [email protected] 1 points 7 months ago

I had a similar problem recently. I switched to a titanium heat break since I apparently have a habit of tightening the aluminum ones a bit too hard, and it was fine for a while but I started getting clogs basically every print at about the 10 minute mark that seemed like heat creep. I couldn't figure out what the deal was since titanium should be even better about heat creep.

It turned out that the machining for the heat breaks might have been too rough I think? Or at least not "perfect" in some way. I had a ton of problems until I "seasoned" them with mineral oil. Basically throw a couple drops in the heat break with it at about 250. Obviously be very careful since it's flammable. You could probably accomplish something similar with an old school filament oiler.