3DPrinting

15789 readers

319 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 2 years ago

MODERATORS

Major issues with klipper and bed levelling (feddit.dk)

submitted 10 months ago* (last edited 10 months ago) by [email protected] to c/3dprinting

15 comments fedilink hide all child comments

I recently made the switch from the marlin-based stock firmware on my anycubic kobra 2, to klipper. I didn't have issues with bed levelling or first layer on the stock firmware, but I'm having significant issues running klipper. The bed is uneven, the probed mesh shows a deviation of 0.197mm, it was the same when running stock FW+octoprint.

But it seemed to be correcting just fine for this on the stock FW. I got a consistent decent first layer across the entire bed.

With klipper, it's absolutely impossible to get it to correct for this unevenness. Half the bed will get perfect first layer, but then the second half is either way too squished or hardly connecting to the bed. And it's causing further issues as it's also hitting the print when moving, despite having Z-hop of 0.3mm for travel moves.

What the hell is going on? How do I fix this?

you are viewing a single comment's thread
view the rest of the comments

[–] felipesoc 1 points 10 months ago (1 children)

Is the problem along the X Axis? Maybe you have X Axis Twist. Measure z offset on opposite ends of the bed along X. If they are different you need to enable X Axis Twist Compensation.

[–] [email protected] 2 points 10 months ago (1 children)

I already have axis twist compensation enabled.

[–] SzethFriendOfNimi 1 points 10 months ago* (last edited 10 months ago) (1 children)

I literally went through this the other day on my franken-ender 3v2. Re-leveling the bed, even tried axis twist compensation.

I’ve been using Klipper on this thing for a few years and overall it’s been good but finally decided to figure out why I couldn’t get even extrusion across the entire bed even with my klackender probe.

After days and days of trying to adjust, tighten, loosen screws, redo hot end to be sure it was properly mounted, even axis twist compensation (which it definitely was) I just went back and just took it apart and redid the frame. Making sure it was square, nothing was overtigtened, that the vwheels weren’t binding, tightened just past there being any “slop”, etc.

Then I removed the compensation hoping that the issue was mechanical and what do you know, it worked.

I had way over tightened some things obviously and so just going back to the foundation fixed the issue.

It’s working great now and klipper properly works with the slight warped bed of my Ender.

[–] [email protected] 2 points 10 months ago

Yeah i actually ended upndoing something similar. Took the hotend and entire bed assembly apart, cleaned and lubed the rails and reassembled. It's been working fine since.