DIY

Due to lack of well designed buyable solutions, I built my own bicycle stand from scratch.

BOM:

• 14 Mtr. 3030 aluminum extrusions
• 48x M8*16-25 Button Head Screw
• 6x Feet with mounting Kit for 3030 Profile
• 10x 90°-Angles for 3030 Profile with mounting kit

Tools:

• Screwdriver with bits for screws
• Drill
• Drillbit 6-8mm
• Allen Key
• Chopsaw 1)
• M8 Tap 1)

Guide:

1. Cut extrusions to length 1) (F.e. 50cm spacing, 5cm tire width 50cm tire slot lenght, 25cm elevation. You'd need 1x2m, 20x50cm, 2x83cm, 10x11cm, 2x25cm)
2. Cut M8-Thread into 20x50cm, 2x83cm and 2x25cm 1)
3. Drill 6-8mm holes into 3030 Profiles corresponding to M8-Thread locations.
4. Fit Everything together.
5. Profit

1. Only nececary if you cut the extrusions to length yourself. If you order the correct extrusion length pretapped you don't need those.

Thank you for the replies yesterday about my drill. I think I'm going to get a cheap corded SDS drill and some big bits. This is what I need to feed through the wall and there is no way to detach the cable from the camera and feed it the other way. I know it needs to be weather shielded, but this is a mad amount of connectors!

The icon is a little different to what I've seen on others and I don't know how to tell otherwise.

Thanks!

How are these usually attached to the wall? Can I just pry them off or would that damage the drywall?

And follow up questions: how can I reproduce that texture when painting the newly exposed areas of the wall?

Does anyone know the best way to make this ramp nonslip? We get a fair amount of ice and snow and there are a couple elderly folks using the ramp.

We tried a basic nonslip rubber mat, but the grooves just hold ice and snow so don't really help.

Our current ideas are maybe adding rubber stair treads every board or two, or maybe tacking little strips of wood to every board.

I'm looking to install some cutoff switch on this 3-pin connector. It almost looks like a PC 4-pin 12v connector, but it actually connects to a Broan CRV motor. Specific model is the L150L.

I originally wanted a ventilator with a timer, but they installed an inline CRV (intake only) with a crazy 150CFM for a tiny 480sqft suite. Massively overkill, and loud. I'd prefer to put this on a timer, or even better would be a smart switch control. But at the very least a manual switch would be great.

For now, and for the last two years, I just have this unplugged, as shown in the image. The passive ventilation on the connected ducting has been more than enough to turn the air around. But sometimes it'd prefer to enable the intake for a time. I just can't have it on all the time because the air turnaround is nutty, not to mention the blast of cold air in the middle of winter.

Any ideas for a switch that fits this connector, or a DIY switch, and/or something to hook to a timer, OR smart switch somehow?

Hi

I installed a circular flap on my ducting for my bathroom vent. This was because outside air was spilling into the bathroom. I've installed a round flap on the ducting which is meant to sit closed unless the the extractor fan pushes air against it to open. It does work but also air from outside seems to swing it open, so I can hear it flap open and close during windy spells.

It's located in the loft about 20cm after the extractor unit, with the remaining 1m og ducting going into the sophet fascia before exiting downwards outside.

Is this something as silly as putting the flap on backwards? I assume not as the flap would be closed when the fan is on and there hasn't been any extractor issues.

Not sure how it happened but my inclination is dry Rot. I don't see much of any mold or mildew around and the room does not feel damp or smells moldy so I'm really not sure if fungus is the cause. I'm trying to finish the space and frame a wall under this joist but I'm afraid that I won't be able to nail into it since it looks like shredded paper. I looked up some techniques to strengthen floor joists so my main ask is:

What is this? How does it happen? And how can I repair it DIY? (Some people online recommend consulting a structural engineer, but I'd rather not if possible) I was thinking of sistering the joists, but with it being a pocket joist I'm not sure if that's ideal.

Added a second picture for what I think is the dry Rot, but it looks small and not dangerous?

[email protected]

Any great ideas on how to pull the outlet forward without pulling the panel off? I’m thinking I might be able to cut the board enough to get the outlet tabs out but still hide the hole behind the plate.

Some years ago, before LEDs were a thing, I bought an Ultrafire WF-500 Flashlight that features a Xeon light bulb. As you might imagine the bulb reached its lifetime and burned away.

Now a replacement bulb is available here https://www.ebay.com/itm/321916301663 the thing is that it will cost me 35€ and for that price I could just buy a new LED flashlight.

Now I was considering trying to adapt a generic LED bulb like this one here https://www.aliexpress.com/item/1005002419159094.html?mp=1.

Anyone else with this model of flashlight succeed at a similar mod? Any LED bulb recommendations? Or... is there any other source for the original bulb at a lower cost?

Some photos:

• https://cdn.tcb13.com/2023/wf500-bulb.jpg
• https://cdn.tcb13.com/2023/wf500-bulb2.jpg
• https://cdn.tcb13.com/2023/wf500-bulb3.jpg

Thank you.

Braille displays can be expensive, so this project idea focuses on making them cheaper and open source

cross-posted from: https://jorts.horse/users/fathermcgruder/statuses/110789232582943740

What's a good torque wrench to get?

I want to replace the spark plugs in my car and I'm apparently going to have to torque them to 30Nm. #diy #tools

@tools

Don’t know if anyone is interested. I normally do videos on car restoration, but decided to film myself building a new garage.

Crosspost from https://lemmy.world/comment/213388

Not sure how to link or crosspost yet, im a Rexxitor, but I built this from scratch, including the the wall framing, drywall, cusom mortar shower pan, and the hardwood floor insert. It was 98% complete here.

Hi all,

This is the beginning / starting point to move DIY over here. :)

Feel free to start using it.