In my area I see old beds thrown out pretty regularly. I try to collect the bed rails since they're usually made from a single piece of maple or oak. I've made a few thresholds from them.
this post was submitted on 27 Jan 2025
186 points (98.9% liked)
Dull Men's Club
1456 readers
475 users here now
An unofficial chapter of the popular Dull Men's Club.
1. Relevant commentary on your own dull life. Posts should be about your own dull, lived experience. This is our most important rule. Direct questions, random thoughts, comment baiting, advice seeking, many uses of "discuss" rarely comply with this rule.
2. Original, Fresh, Meaningful Content.
3. Avoid repetitive topics.
4. This is not a search engine or advice forum.
Use a search engine, a tradesperson, Reddit, friends, a specialist Facebook group, apps, Wikipedia, an AI chat, a reverse image search etc. to answer simple questions, identify objects or get advice. We accept very few questions, and they must be over topics much more difficult than what is easily discoverable with a search. Also see rule 1, “comment baiting”.
5. Keep it dull. If it puts us to sleep, it’s on the right track. Examples of likely not dull: jokes, gross stuff (including toes), politics, religion, royalty, illness or injury, killing things for fun, or promotional content. Feel free to post these elsewhere.
6. Not hate speech, sexism, or bullying No sexism, hate speech, degrading or excessively foul language, or other harmful language. No othering or dehumanizing of anyone or negativity towards any gender identity.
7. Proofread before posting. Use good grammar and punctuation. Avoid useless phrases. Some examples: - starting a post with "So" - starting a post with pointless phrases, like "I hope this is allowed" or “this is my first post” Only share good quality, cropped images. Do not share screenshots of images; share the original image.
8. All polls must have an "Africa, by Toto" option. Why? Because we hear the drums echoing tonight.
founded 2 months ago
MODERATORS
That is brilliant!
Waste not want not.
Showing any type of skill at craftsmanship is veering way out of dull territory.
I may have to go lie down for a bit.
Looks better than anything you could've bought at the store; nicely done!
Thank you Friend!
not dull at all!
Nice work!
Very nice! How did you go about it?
I picked up a piece of hardwood that was 5/8 inch thick. Just measure the gap under your door so you know how tall the threshold can be. I went with a 3.5 inch width to cover the floor's expansion gap with room to spare. I just cut that down to the width of the door. Then I used a router to put a 45 degree chamfer on all 4 sides.
The 45 degree angle goes down about half way, I just ran a scrap piece through the router and progressively raised the bit until the angle felt right, then did it on the final one.
Gave it a light sanding to remove any splinters and then I just stained it to match the floor and used a rubber mallet to get it in place. It's pressure fit, so it's a little tight to hold it in place. Some people opt to screw them into the floor below instead.
Dropping a few brads/nails into it to hold it into place is a good idea. As time goes by, wear and expansion/contraction of the flooring will have it popping out.
I picked up an airgun to put in 2 1/2" finishing brads on the floors I did (engineered hickory). Turned the air pressure up to the maximum the gun was rated for (150psi) and sunk the brads into the board
That's a good idea, thanks!
I also hope you did 5+ coats or so of polyurethane or shellac on it. Jams tend to take a beating. The slight rise means that everything hits them. I had to learn that one the hard way.
I'm curious about this too, I've been trying to find an aluminum threshold I can modify but this might be easier.
That was my issue too! With the floor's expansion gap, it needed to cover about 2-2.5 inches in width. Everything in that range was more for industrial or exterior use. The S4S oak plank I used was $16, with pre-made thresholds being $25+. Of course, tooling is a limitation. You'd at least need access to a router to make this.
You’d at least need access to a router to make this.
It could be done with a saw and a block plane.
I've been looking for an excuse to buy one for a while.
I'm just wondering, is it common to have that big a gap under your doors where you are?
I'd stub my toe on that, fuck me 😂
These thresholds are usually about 1-2cm raised and have sloped sides to specifically avoid catching toes.
They're very common in north America
Very nice
Is that treated/engineered bamboo laminate flooring? I think I have the exact same stuff from Home Depot.
Sure is! I got it from a local flooring store and installed it myself years ago. It's hard to beat the price and hardness.
Yeah, I put mine in 8.5 years ago, and with a large dog, 2 cats, and 3 kids, it's held up remarkably well. The only problem I've run into is some of the tongue-in-groove connections have pulled apart over time creating small (maybe 1/4") gaps, but the planks themselves have been great. And frankly, that is probably a combination of installation error (by me) and us living in a pretty harsh environment with a huge number of freeze-thaw cycles and lots of snow every year (with a shitty insulation job in our crawlspace).
Nice! Mine is probably around 8 years old now. I had one section pull apart like you were saying, so maybe not user error. I ended up pulling up that section, replacing any price that seemed suspect, and glued the joints during reinstallation. That's actually what drove me to replace all the old T mold thresholds. But yeah, just that one defect across 900SqFt (84 SqM) isn't bad.