Home Improvement

9037 readers

2 users here now

Home Improvement

founded 1 year ago

MODERATORS

nieceandtows

nichos

[email protected]

Replacing Bathtub Faucet - Pipe Recessed in Wall (lemmy.today)

submitted 1 year ago by [email protected] to c/homeimprovement

5 comments fedilink hide all child comments

The shower diverter in our spare bathroom doesn't really work. The faucet is also gross and I want to change it.

I took the faucet off the wall and the pipe doesn't match what I'm seeing in videos. My faucet doesn't quite match the ones at Home Depot.

Most instructions I'm seeing show the pipe coming out of the wall:

My pipe is recessed in the wall:

My faucet has a piece of pipe extending out of it:

All the faucets I see in stores or online don't have any pipe on them. They're expecting the pipe to be sticking out of the wall.

Do I need to find a piece of pipe to make an adapter? Or is there a type of faucet I should be looking at that has this connection?

top 5 comments

sorted by: hot top controversial new old

[–] [email protected] 8 points 1 year ago

This is just a 1/2” nipple to extend into the tub.

A) this has been leaking for quite some time based on the way the inside looks- I would investigate before installing another nipple.

B) get the right sized nipple, but also you will need to seal around that hole- 1/2” pipe and 1” holes don’t math very well.

C) make sure the new nipple ( or previous reinstalled) is tight enough to not have leaks, I suggest maybe buying a bit of some better Teflon tape or a small amount of pipe dope to help with the process.

[–] [email protected] 5 points 1 year ago (1 children)

Are you sure the pipe extending out of the faucet just isn't stuck on there and can be removed? If so, just take it off and thread it back on to the wall and then you can use any normal faucet from HD. I have one similar to that when I was replacing my shower head and noticed it was getting stuck to the head rather than staying in the wall.

[–] [email protected] 1 points 1 year ago (1 children)

It does look like a separate piece, but I can't remove it. It's stuck.

[–] Bigtiddygothgrany 3 points 1 year ago* (last edited 1 year ago) (1 children)

No it's probably corroded, so you need pipe dope, Teflon tape, channell locks, white caulk, just a small squeeze tube, and a half inch galvanized nipple, (brass is preferable but it's more expensive) also when you get the new tub spout make sure it is also threaded, the ones that tighten to copper are fairly popular so make sure you get the threaded kind.

Now the nipple should be the same size as the old one so just bring the spout with you to the store, I would also suggest grabbing a 1/2 inch size longer and a 1/2 inch size shorter, just in case. It also doesn't hurt to show one of the employees what you're looking for if you have the spout with you.

Now when it comes to installing, do about 4 wraps of Teflon around each of the 2 threads, then wipe pipe for over those threads as well. Using the channel locks, tighten it onto the spout as much as you can first, then tighten the spout onto the threads behind the wall. You of course want it to be flush with the wall but if it doesn't make it home all the way but is very close that's okay. Turn it on make sure there's no leaks, Then caulk around it afterward, most caulk you need to wait like 24 hours.

Oh I almost forgot, when tightening the spout to the wall do not use the channell lock for that, if you do you will scratch up the finish. Just use your hands to tighten.

[–] [email protected] 1 points 1 year ago

Thanks. Very helpful.