overview for UnH1ng3d

0.2 owners - Bed heat time? in c/vorondesign

[–] UnH1ng3d 2 points 5 months ago (2 children)

I don't think anyone has a v0.2 in this instance 😅 Thanks for going out of your way to answer my question, even though you can't 🤣

I'm wanting it because I realise I do a lot of very small parts and I often want to iterate on them quickly, so a fast bed heat would be quite nice. I currently always heat soak for bed meshes and such, but I haven't found it necessary for prints - they're usually not that big though 🤷‍♂️

Do you know where I can find that documentation on max heating?

0.2 owners - Bed heat time? in c/vorondesign

[–] UnH1ng3d 1 points 5 months ago (4 children)

Thank you 😁

That's extremely helpful, and I didn't even expect a reply after this time.

How many watts is the heater you are using?

I'm thinking of buying a used 0.2 and I wondered if it might be fun to change to an AC bed. I read the original v0 had one but some kits were using improper solid state relays so they changed it for safety 🧐

I certainly see you the chamber heat argument for ABS 💪

Why do bed slingers heat faster?

Disable resizing clip to fit inside the project's resolution? in c/[email protected]

[–] UnH1ng3d 2 points 6 months ago

💪

Does anybody else feel guilty being suspicious of anybody in a black hoodie with the hood up? in c/[email protected]

[–] UnH1ng3d 10 points 7 months ago (1 children)

You can't trust what you can't see.

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 1 points 7 months ago

This was it! I had my 10-25% (not degrees 😅) overhang speed set not to slow down at all. I now have it set to 30mm/s and I have a perfect result. Thank you 👍😁

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 1 points 7 months ago (1 children)

Sorry, I didn't follow that. Top layer of what? Not the actual top, top layer right?

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 2 points 7 months ago

You may actually be right even though I thought I had checked this. Orca's overhang speeds are based on overhang percentage and not angle, I previously just looked at the number and assumed it was degrees 🤦‍♂️I will match the speeds for all overhang percentage ranges and see if that solves it 🤞

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 3 points 7 months ago

Thanks. I'll experiment with temperatures first but I've got some different filament on the way too as it happens, so hopefully I'll manage to escape the problem one way or another 😁

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 1 points 7 months ago

Thanks, I'll give it a go.

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 3 points 7 months ago (6 children)

It starts just underneath actually, but it still could be related 🤔 Maybe I need a test without numbers.

[SOLVED] Any ideas what causes this in overhangs? in c/3dprinting

[–] UnH1ng3d 3 points 7 months ago

Thanks guys. I will try both and see what works. My layer adhesion is good / parts are strong though.

Laser printer lines across page 🤔 in c/copiers

[–] UnH1ng3d 2 points 7 months ago

I didn't think to look on Ali. You even removed the tracking part from the link too 😉 If it turns out to be that, I'll buy one and replace it. Thank you