Fubar91

joined 1 year ago
[–] Fubar91 8 points 11 months ago (1 children)

Same here in Canada. I think its legitimate learners. Not sure why you think age has anything to do with it, theres no max age to learn to drive. Hell, my late grandma didn't get her licence/learners permit until she was in her 60s.

Could be related to an influx of immigrations as well, plenty of people didn't have the luxury to get a drivers licence or own a vehicle.

That or people are just too lazy to remove them haha.

[–] Fubar91 22 points 11 months ago (1 children)
  • No shitty P2W mechanic bullshit.
  • Full game on release.
  • no always online requirement.
  • not completely unplayable at launch tripple A title.
  • content amount is worth its purchase value.
  • community mod support, which drives improvements and long term playability.
  • Development transparency on what the game is and where its headed.

Does it have bugs, of course, nothings perfect.

Can't say too many games on the scale of BG3 came out this year that can check as many boxes. It takes GotY for me as well personally.

[–] Fubar91 54 points 1 year ago (1 children)

Yuup, this is why i started pirating again, which i haven't done in a long while.

[–] Fubar91 4 points 1 year ago (1 children)

Haha found th issue, buddy wasn't saving and confirming the bios setting changes. Made sure he did this time and it's running as expected with the gen 4 option.

[–] Fubar91 2 points 1 year ago (3 children)

Yeah im thinking a similar thought. Ill see if he can locate one to test with. If not I'll send him to a local shop so they can test it. Unfortunately lives 1000km, otherwise id beable to do some better testing for him haha!

Thanks bud!

[–] Fubar91 2 points 1 year ago* (last edited 1 year ago) (5 children)

Yep k series has igpu, igpu works fine.

Output works fine from the 2080 if in the 4x slot, detects in windows and all is good with the driver installation.

It just straight up doesn't detect the GPU in device manager at all, and the driver installer didnt detect it only while in the top pcei 5x slot.

Sorry for the rushed response, at work atm.

[–] Fubar91 1 points 1 year ago* (last edited 1 year ago)

Fresh windows install, mobo drivers and chipset drivers installed. I'll double check with him on the versioning and if he just did it via windows update or directly through the manus support page.

Sorry for the rushed response, at work atm.

5
submitted 1 year ago* (last edited 1 year ago) by Fubar91 to c/buildapc
 

Got a strange one here, and im sure im missing somthing simple.

Buddy of mine did a mobo, ram, cpu upgrade on his own and is running into some issues with the PCIe 5.0x16 slot not detecting his 2080 in windows device manager. Strange part is it works 100% fine in the slot below thats the 4.0x4 slot.

Specs: 14700k cpu MSI z790 pro-a wifi mobo Zotac 2080 Ddr5 6200mhz ram (currently just set to stock without xmp until i figure out the pcie issue) Win11 home 1 sata6 ssd samsung, 1 m.2 nvme ssd samsung. 1000w seasonic psu

I tried swapping the bios settings for the pcie lanes to gen 4 instead of auto.

Confirmed with him the connections to power and board are well established thrice.

Mobo is on the latest firmware from msi.

Ez debug leds dont show any VGA/display errors in either slots.

GPU has power and fans spin up whilein the 5.0x16 slot.

Im honestly stumped on this one and what to try next or look out for. Have a feeling im probably missing somthing simple here.

MSI support hasn't been responsive so im posting here as a last attempt to gather ideas.

Edit: buddys not the brightest star. He wasn't confirming the bios changes, he was just exiting out... swapped the pcie setting from auto to gen4 and made sure he saved them. Working good now.

[–] Fubar91 1 points 1 year ago

Its on the opposite side of the room, roughly 10-12feet away. Good suggestion however!

[–] Fubar91 3 points 1 year ago* (last edited 1 year ago) (2 children)

Yep, one in the utility room by the furnace, one in the upstairs front door closet beside the kitchen, and one in the garage. Haven't had to use them for myself personally... but the neighbours came slamming on the door a few times needing one.

IMO every residence should have one handy. Never know what could happen or who might need one. I really should get one thats rated for electrical fires however.

[–] Fubar91 20 points 1 year ago

Unfortunately a lot of consumers don't understand this. Even if they use "pro" apps daily. These same people will fall for Apples marketing tricks here regardless.

[–] Fubar91 7 points 1 year ago

Let's be real bud, there'd be a Tims on each side of the bridge, and ones always outta chocolate timbits.

 

Good day everyone. Been into the hobby since around 2014. I own 3 FDM printers currently.

Started on a Ecker Tech reprap kit.

Got a Wanhao D3, modified the hell outta it.

Latest as of a few years ago is a Ender 5Plus, have a CoreXY kit on there, swapped the board to a 32bit BTT, and added a microswiss extrusion assembly.

The FDMs have done me well over the years, and I've highly enjoyed tinkering around with them. But now I have the itch for something new and fresh. I'm thinking of dipping my toes into the resin printer market, and am looking for some reccomdations and experiences of fellow 3D printer enthusiasts.

I'd like to keep it around $2000 CAD (roughly 1500 USD, ouch CAD lol). I'm no stranger to tinkering and modifying. Have a shop with plenty of space, ventilation, and what not.

If you have any suggestions on a new FDM printer I'm all ears! (Maybe somthing multi-filament compatible?) So feel free to suggest some as well.

Thanks in advanced!

view more: next ›