You'll see the real performance problems in Act 3. Unless they manage to fix it with the Xbox port.
Personally I run almost everything on low (except for Textures) but with FSR 2 activated. Looks great and runs great.
this post was submitted on 25 Nov 2023
18 points (87.5% liked)
Steam Deck
13934 readers
238 users here now
A place to discuss and support all things Steam Deck.
Replacement for r/steamdeck_linux.
As Lemmy doesn't have flairs yet, you can use these prefixes to indicate what type of post you have made, eg:
[Flair] My post title
The following is a list of suggested flairs:
[Discussion] - General discussion.
[Help] - A request for help or support.
[News] - News about the deck.
[PSA] - Sharing important information.
[Game] - News / info about a game on the deck.
[Update] - An update to a previous post.
[Meta] - Discussion about this community.
Some more Steam Deck specific flairs:
[Boot Screen] - Custom boot screens/videos.
[Selling] - If you are selling your deck.
These are not enforced, but they are encouraged.
Rules:
- Follow the rules of Sopuli
- Posts must be related to the Steam Deck in an obvious way.
- No piracy, there are other communities for that.
- Discussion of emulators are allowed, but no discussion on how to illegally acquire ROMs.
- This is a place of civil discussion, no trolling.
- Have fun.
founded 2 years ago
MODERATORS
What do you run textures at? I'm always on the lookout for the best SD1.0 setup for me.
Medium
But if you don't play long sessions higher values should be feasible. Textures mostly just impact VRAM and not performance.
I agree act 3 is where it will struggle. I lock to 30fps with gamescope, then fsr2 at ultra quality or quality with everything at low except for animations and textures.
You could go higher with framerate but this is smooth and works for me
What is gamescope? I read the github Readme, but it doesn't describe what it does
Gamescope is just the compositor that the Steam Deck uses to display the game for you. When you use the FPS limit in the "..." menu, you lock the fps via gamescope.
Ultra doesn't seem to cause any performance issues? You sure?
I run the game with low to medium settings with FSR2 enabled, FPS capped at 30 but frame times are still all over the place.
I haven't noticed anything yet, but it's only been a day since I got the oled. I'm in the grymforge where there's is a lot of lava, and all 8 did was turn the ultra preset on. I didn't touch the FSR or cap any frame rate. Things look smooth, and no stuttering, maybe I am not in an area where I'd notice, or maybe FSR and frame rate cap are causing you issues?
I just checked the game out again on the Deck.
I tried playing at Ultra without any FSR(2). And sure, technically relative performance isn't that much worse so if you don't really care about FPS dropping into the teens and averages being below 30, I could see you playing at Ultra.
Then I set it back to my preferred settings (Medium preset, FSR2 Balanced), and it's a night and day difference. It has headroom to go above 30 FPS, but I cap it to 30 for what is very consistent frame delivery it seems. I don't remember it running this well, but recent Steam OS and game updates probably improved things.
So I'd recommend Medium preset + FSR2 Balanced or maybe Quality. Then I'd cap it to 30 FPS because frame times are all over the place otherwise. You can then turn down the TDP until you start seeing frame times getting worse. 10 watts didn't seem to perform too bad for me. It doesn't look much worse from Ultra considering the size of the Deck's screen.
Full disclaimer that I have the first generation LCD Steam Deck though. Your OLED model might have a slight performance/efficiency advantage, but the core experience will be similar. I also undervolted my Deck's APU. You could try lowering TDP even further from the 10 watts I tried though to increase battery life ever so slightly.
All that being said, if you're fine playing it at Ultra, by all means do it. There's nothing wrong with that.