this post was submitted on 30 Jul 2023
2 points (100.0% liked)

Arduino and other electronics projects info

125 readers
1 users here now

founded 1 year ago
MODERATORS
[email protected]
2
Taotao 684270 Hoverboard Gyroboard serial readout with arduino (lemmy.staphup.nl)
submitted 1 year ago* (last edited 1 year ago) by [email protected] to c/[email protected]
2 comments fedilink hide all child comments
 

I've got a few damaged hoverboards. They're not very good quality. Some work others go into error-state after a while.

To be able to do some fault finding i thought to try to readout what these sensorboards provide.

This is the exact model i have

Sensorboard gyroscope taotao 684270 2016-04-20 (where i found the pics: https://www.voltes.eu/products/hoverboard-sensorboard-gyroscope-taotao)

i use the Arduino mega 2560, because it has multiple UART pins.

Baud rate

I first needed to know the baud rate. For that i found some online arduino code measuring the shorted pulse duration, and based on that determine the baud rate. Seems the board is communicating at 57600 baud.

which UART mode

To try to find out what UART mode is used, i created a program which determines the high/low durations of the data pin, and print it as a bitstream, hoping to be able to determine the mode. But i couldn't make sense of it(in hindsight, i can understand it, but i'm too much of a rookie). So i just tried the few available modes. None of the 5 to 8 databits modes produced anything useful.

9 bit data

Turns out the standard Arduino 8 bit UART modes don't work. i needed to try the 9 bit UART mode. For that i used an external library mentioned on this site: https://forum.arduino.cc/t/9-bit-software-hardware-serial/590266/8 Because this library sets an interrupt routine, i renamed the HardwareSerial9bit0.cpp file to HardwareSerial9bit0.cpp.txt so that in my sketch it didn't collide with the Arduino IDE's Serial which i used for debug printing to the Arduino console. The mode which worked for Serial91 is SERIAL_9O2 (9 databits, Odd parity, 2 stopbits )

Finding a frame

To find the start of a frame, i decided to look for a 0, then 2 times a non-0, and a 0 after the frame. For storing the UART data in a buffer, i used the CircularBuffer library by AgileWare v1.3.3 https://github.com/rlogiacco/CircularBuffer . I set it to store 512 integers. When Arduino finished 1 cycle, there are between 10 and 60 integers read into the buffer. But when i enable printing of packets to Serial, then it increases to about 70 - 80 per cycle which are available. When the cyclical buffer contains more then 10 integers, i test if it contains a valid frame, if not, i remove the head, and test again. Update: I changed the frame detection because an actual 0 angle would not be possible. So now it tests for #0 to be 0, #5 to be 0x5 or 0xA, #10 to be 0. Also, i now realize that UART overflows at 64 characters.. i.e. the code must be improved to be faster. /update

Data obtained

The data packets are formatted as

 * 000,102,002,102,002,01A,0B8,0B8,000,000,000,
 *     AA  BB  AA  BB  CC  DD  DD  EE  EE  FF
 * 000   = Start of frame
 * AA BB = LSB,MSB  forward backward angle
 * CC    = Status bits ( 0xA unpressed, 0x5 pressed, 0x20 Error/was upside down )
 * DD    = 9 bit unsigned 0..185..368 intertia left/right       rotation
 * EE    = 9 bit   signed -255.. +255 intertia forward/backward rotation
 * FF    = Start of next frame

Data issues

The doubling of the data in a single frame enables some error checking. I observed the next issue

AA   BB    AA   BB   CC  DD  DD  EE EE  | 'AABB as dec nr' || Bad
Angle reading is dodgy.. Bits are flipping on.offf
V     V    V     V         
63 | 1E1 | 63 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15773 || 
63 | 1F1 | 63 | 1F1 | 5 | B8 | B8 | 0 | 0 | -7581  || BAD
73 | 1E1 | 73 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15757 || BAD
63 | 1E1 | 63 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15773 || 
63 | 1E1 | 63 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15773 || 
73 | 1F1 | 73 | 1F1 | 5 | B7 | B7 | 0 | 0 | -7565  || BAD
63 | 1E1 | 63 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15773 || BAD
73 | 1F1 | 73 | 1F1 | 5 | B8 | B8 | 0 | 0 | -7565  || BAD
63 | 1E1 | 63 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15773 || BAD
72 | 1E1 | 72 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15758 || 
62 | 1E1 | 62 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15774 || 
62 | 1F1 | 62 | 1F1 | 5 | B8 | B8 | 0 | 0 | -7582  || BAD
62 | 1E1 | 62 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15774 || BAD
62 | 1F1 | 62 | 1F1 | 5 | B8 | B8 | 0 | 0 | -7582  || BAD
72 | 1E1 | 72 | 1E1 | 5 | B8 | B8 | 0 | 0 | -15758 || BAD

But i actually can't figure out which of the reading is 'BAD' i just picked the one which changed much in angle from the previous frame, while accelerometer(EE) says 0. i figured that if the angle changes much, then the accelerometer should also indicate movement.

Statistics

After logging the packages and trying to find a way to read only valid frames, i used an LCD 20x4 I2C screen to show some statistics. For that i used LCD Library by Frank de Brabander v 1.1.2 https://github.com/johnrickman/LiquidCrystal_I2C

I show a databar for the

  • forward/backward angle
  • forward/backward accelerometer
  • left/right-turning accelerometer

and the following info

  • Err/Ok (upside down etc)
  • On/Off (standing on the pedals)
  • %BP (Percentage Bad Packets. A packet is bad when the doubled data isn't the same)
  • BA (amount of 'Bad Angle' packets)
  • BL (amount of Bad Line incidents. i.e. not able to find the starting '0' data of a frame. Testing for nr #0 = 0(start) and #10 = 0(next start), and #1 and #2 are non-null.)

My total setup looks like this

For the presentation not to take too much CPU time, the top 3 bars refresh every 100 msec, the bottom numbers refresh every 500 msec. i Also changed LiquidCrystal_I2C\LiquidCrystal_I2C.cpp to set the I2C speed to 400Khz by calling setClock()

void LiquidCrystal_I2C::init_priv()
{
	Wire.begin();
	Wire.setClock(400000); // Set I2C to 400Khz
	_displayfunction = LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS;
	begin(_cols, _rows);  
}

Next up.. Trying to figure out what sensor-data is acceptable by the main board and which data makes the main-board go into error state.

top 2 comments
sorted by: hot top controversial new old
[โ€“] [email protected] 1 points 1 year ago

[โ€“] [email protected] 1 points 1 year ago* (last edited 1 year ago)

Turns out my UART buffer is overflowing.. So i tried to use the serialEvent() routine to process the incoming data before it overflows.

But according to this https://groups.google.com/g/diyrovers/c/XptH9f7zLxA/m/0apw-2jmAAAJ The function actually isn't called by interrupt;

I found out this weekend that is not quite right, it actually looks like this:

int main() {
   setup(); 
    for (;;;) {
       loop();
       if (serialEventRun) serialEventRun(); 
   } 
   return 0; 
}

What this means in practice is that if you don't return from loop() or setup(), your serialEvent() function(s) won't be called. I suppose that you could call them yourself, or call serialEventRun(). But, it is a bit surprising; I always thought that serial events were attached to an interrupt, not so though. I learned this the hard way this weekend, when I tried to add a serial interface for debugging.

Also, curiously, on a teensy 3.x, adding a delay() call causes serialEventRun() to be called. I haven't tested this with an Uno yet, but it would make sense to have that bit of code in delay().

update

I changed from updating the LCD in one go, to updating one line per 100msec. Now the buffer keeps filling up to about 10-20 integers. Ofcourse, when i enable serial printing for debugging, then the UART buffer overflows regularly.

But still, sometimes the incoming data doesn't match a packet. Like a character is missing. i read that Arduino just removes a character if there was a parity error. there's no way to detect the the error. Maybe that's what's happening.