this post was submitted on 17 Jun 2023
14 points (100.0% liked)
homeassistant
12140 readers
18 users here now
Home Assistant is open source home automation that puts local control and privacy first. Powered by a worldwide community of tinkerers and DIY enthusiasts. Perfect to run on a Raspberry Pi or a local server. Available for free at home-assistant.io
founded 2 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
Thanks for the advice, I'll look at the docs.
How's your RAM usage for HA? The pi I have is only 2gb, already runs pihole but I can buy another/run HA on my server, but if I don't need to, then I won't.
I ran HA on a pi 3 and then upgraded to a NUC with a Celeron using 4gb of RAM mostly because I used Plex at that time and needed better transcoding.
You can try running HAOS supervised on your Pi. Running supervised will let you run addons within HA such as pihole, Zigbee2mqtt, Mosquitto, Node-RED and others. After that, you can verify if you actually need to upgrade your hardware. You'll probably be fine with that amount of RAM.
When you switched from pi3 to NUC , did you notice any performance improvements? I'm asking because I run my setup on a rpi3 and it mostly works ok, but the latency is sometimes high, so I'm wondering if upgrading the host will improve things.
For me i did. It was buggy on a rasp all the time. Plus from time to time memory would clog up and the instance would stop functioning. Haven't had any issues since upgrading to the nuc. It just works and I migrated all devices to USB radios. So Bluetooth, Zigbee, zwave, serial power meter, serial heat meter, serial ups, everything just connects without hubs or anything.
Would definitely recommend! Just get a cheap second hand one on eBay or so.
I didn't, but because the pi already worked fine and didn't have many addons running. I have since introduced tailscale, diyhue, frigate without a tpu, etc and the nuc has been rock solid (even with 4gb of RAM and a Celeron J3455).
I think it comes down to what addons you run and what type of storage you use (if you're using an SD card on your pi, you might want to boot from an SSD instead). Also if your zigbee dongle is old like the Nortek one, you might see improvements in responsiveness when upgrading to a zigbee 3.0 stick.
I have a newer ZigBee 3.0 dongle and run a few add-ons, but nothing big - z2m, nodered, mosquito is all I use. I will upgrade anyway, but I'm not in a hurry, it works fine, apart from an occasional delay in switching, which might be network related.
Just wondering how you set up the Hue bulbs, did you need any workarounds or the bridge? Do they just link up to the dongle?
I have about two dozen Hue bulbs paired to my Sonoff Zigbee stick using Zigbee2MQTT. No workarounds or Hue hub necessary.
Any ZigBee device should just be able to pair with the dongle directly and no other settings or hardware is necessary. Check out the https://www.zigbee2mqtt.io/supported-devices/ , find the particular device/bulb/switch and read the setup steps. If it has any quirks, it will be listed there. If not, you can be sure it will work without issues. I have a lot of Ikea tradfri bulbs, switches and also cheap Chinese devices such as tuya, they all work without issues.
I don’t see any B22/Bayonet Hue colour bulbs that are supported, but other kinds like E27 are there. Is there something about B22 bulbs that’s different? All but 1 of my bulb sockets are B22
Wouldn't know, I only have Ikea bulbs. Those all work. But I think hue is better, since Ikea ones don't dim very low, whereas I've heard Hue ones dim very low. Maybe give the b22 ones a Google search?
I’ve asked in the discord, if I can’t use hue b22 bulbs it’s not an issue, but I would prefer them due to their quality, even though they are more expensive.