Great question, no I am running Jellyfin version 10.10.3 in Linux Mint 21.3.
RVAtom
joined 1 year ago
Thank you so much for your help! I went to that folder and the migrations.xml was a blank file, but system.xml was still okay.
I searched a little about the migrations.xml and found a thread on the jellyfin forum with exactly the same problem so I renamed all of the xml files in the /etc/jellyfin folder and it started back up nicely.
Missed it, better luck next time I guess.
I want to undo some of my setup on my network so I can redo it in a different configuration on the same machine. The first thing I wanted to do was disable my Adguard server, making sure I could still use the internet after.
I thought I had cleared out all of the settings in my router that made it use Adguard for DNS, but when I shut down Adguard afterward, all outside connectivity fell apart. I could still get to websites if I knew their specific IP address, but nothing that needed DNS worked. When I booted Adguard back up, everything started working again.
I have tried several options in the DNS server settings in my Asus router (TUF-AX5400). Is there something I need to do in Adguard first to make this work? Or is this maybe something I need to reset in my Asus router and then give it time and a few reboots to work?
I consistently have a lack of anaerobic load in my Garmin training load. I did a track run today trying to work on intense intervals. I was hoping to get to the end and have more anaerobic effect than aerobic. Is there something I should be doing differently in my runs? I was under the impression that the rest phase between run intervals should allow you to really catch your breath, so I often walk for a few seconds before getting back into a jog in my rest interval.
Should I be more focused on keeping my pace up during the rest interval? Should I be running fewer/more intervals? Should I ignore these stats and just enjoy the run?
I was surprised to see Alcala optioned down to make room for Theibar. I'm not sure who I would have picked over him, but I'm guessing it was more on who could be optioned, rather than who was the least important.
I get the idea of keeping some depth around. Still a bummer for someone who seemed to be putting it together.
This was my first thought. Not sure if it is a nostalgia thing or if it was actually good at this point. I did like it a lot back then though.
I'm looking forward to the R2 coming out. My wife is due for a new car in a few years and I was surprised when she sounded interested in it too. I might just put down a reservation
So this definitely seems like the guide that helped the most. I spent more hours than I would like to admit working on this over this weekend.
I am trying to figure out if I have a way to do what I want to here. When it was all said and done I could no longer log into the remote computer I was using to run my Jellyfin server. I have been messing around a little bit using a Linux PC with that, and enjoyed that aspect of things, but it seems like once you get hardware acceleration going, you cannot see the desktop anymore. There were several warnings about this so I wasn't entirely surprised when it happened.
I think I am going to end up needing to get rid of the proxmox part, and just run Linux directly on the computer if I want to do this, and remote into it. It is currently not hooked up to a monitor and is actually on top of my kitchen cabinets out of the way. It was a fun challenge and I learned a lot I think.
I have never used Feit lights with Home Assistant, but yes, my bedroom lights turn on when it senses motion. That automation disables when my living room lights are off (assuming we turn them off at bedtime) or when my phone plugs in to charge (which I do at bedtime). I use a motion sensor by Phillips Hue, and it integrates directly with the Home Assistant Yellow thru its Zigbee radio without an additional hub.
This is where the 120 volt power makes it a little worse for us Americans. 2200w would be 18 amps, easily taking most of the power on a breaker.
If kettles ever got more popular in the US maybe they could put 240v outlets in kitchens for kettles, but that would be a huge change.
21 miles this week. I had to cut my 10 mile run short yesterday because it was just too hot. It was 85°F when I left for my run in the early afternoon sun. Not a real smart move, but I thought it wouldn't be so bad based on the season.
Running a half in a few weeks and wishing I had run a bit more over the last month.
view more: next ›
I have figured out that I was even further confused. When I went into the disks program to figure out what type of partition was on the drive I realized the drive isn't really at
media/RVAtom/SSDit is atmnt/SSD. That makes a little more sense, as I was confused a couple of days ago that it seemed to be in media without me remembering.Running
ls -lon the correct drive gives: rvatom@rvatom-mint-PC:/mnt$ ls -l total 4 drwxr-x---+ 6 rvatom rvatom 4096 Dec 18 22:00 SSDUnder the disks tool I have gone into mount options and checked "mount at system startup". The drive type is Ext4 I believe. I'm going to try a few more reboots but it seems like Jellyfin is willing to look at this drive now. We may have success.