overview for Prismo

iOS keyboards that don't censor "bad words" in c/asklemmy

[–] Prismo 9 points 5 months ago (3 children)

I added some swear words as contact names, this is one way to get around the fucking censorship

NASA’s Boeing Starliner Crew Flight Test Launch – June 5, 2024 (Official NASA Broadcast) in c/space

Men over 30, do you think you are becoming grumpier as you are getting older, or on the opposite, becoming more relaxed and laid back? in c/[email protected]

[–] Prismo 16 points 6 months ago (1 children)

Yes

Antivax quacks are continuing to make up fantastical biological mechanisms for COVID-19 vaccine “shedding” in c/science

[–] Prismo 10 points 6 months ago

Does mean that the unvaccinated anti-vaxers will keep away from the vaccinated??

What would you like to see in a house IT setup? in c/technology

[–] Prismo 5 points 7 months ago

At least one cat 6 ethernet in each room. Multiple outlets in any media room. One of my old houses had speaker jacks in each corner of the room which was a godsend when setting up surround sound for a home cinema setup.

Is there a term for a gathering of trees in an open field? in c/asklemmy

[–] Prismo 3 points 8 months ago

Copse was my initial thought, but there is also the word Spinney.

https://www.dictionary.com/browse/spinney

A Chinese Humanoid Just Broke the Robot Speed Record—and Now It's a Race Against Time in c/technology

[–] Prismo 3 points 8 months ago

Here’s a Piped link to the video in the article:

https://piped.video/watch?v=83ShvgtyFAg

3

Multiple email signatures (self.ios_community)

submitted 8 months ago by Prismo to c/ios_community

1 comments fedilink

I’ve just switched from multiple email accounts to using the 5 custom domains for iCloud. However, now I’ve lost the per email custom signatures. Is there any way to get this back within the iCloud custom domain setup?

Men Over 30: What's one recipe or dish that you'd consider your go-to in c/[email protected]

[–] Prismo 1 points 8 months ago

Puttanesca or risotto. Both relatively easy to make, tale about 40 mins and are delicious!

Hair probably had an important function at some point in human evolution but now it's mostly cosmetic in c/showerthoughts

[–] Prismo 2 points 8 months ago

I guess I’ve been looking at it wrong the whole time! Although, living in the countryside would be preferable for moustache-rainwater

Hair probably had an important function at some point in human evolution but now it's mostly cosmetic in c/showerthoughts

[–] Prismo 60 points 8 months ago (4 children)

I appreciate the usefulness of my eyebrows to divert rain away from my eyes. I do not appreciate my moustache’s water gathering properties when walking in humid environments.

Do you sit at a desk and keyboard for multiple hours? If yes, please recommend a good chair. in c/asklemmy

[–] Prismo 9 points 9 months ago (3 children)

Surprisingly this chair has come out highly in reviews when compared to 4 figure chairs. I have it and can say it is very comfortable. It’s not going to be the best of the best, however if your budget doesn’t stretch to more than mid-3 figures this could be a good alternative.

https://www.ikea.com/gb/en/p/markus-office-chair-vissle-dark-grey-30261152/

https://www.shortlist.com/lists/best-office-chairs-401080

Your username has suddenly become your only means of staying alive. How bad is it? in c/asklemmy

[–] Prismo 3 points 9 months ago

I’m pretty sure I’d be ok in multiple realities

273

I’ve just turned 40. What advice would you older lemmy users give me? (self.asklemmy)

submitted 9 months ago by Prismo to c/asklemmy

174 comments fedilink

34

Possible over extrusion, any advice appreciated! (i.imgur.com)

submitted 1 year ago* (last edited 1 year ago) by Prismo to c/3dprinting

8 comments fedilink

https://i.imgur.com/yzJg1ne.jpg

https://i.imgur.com/IgVP7Fj.jpg

Any ideas on this new issue only affecting one of my printers, only seems to be on the bottom layers of a base mode print. The layers that are not done as one continuous spiral. Photos are before and after, ignore the banding on the before! (Thats another issue I have fixed)

Can’t figure this one out, driving me mad as I have orders to fulfil

Solved:

So a combination of three changes finally got me back the correct result.

Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
Reduced the temp by 10°C apart from the first layer.

18

Help with intermittent extrusion issue (imgur.com)

submitted 1 year ago* (last edited 1 year ago) by Prismo to c/[email protected]

16 comments fedilink

Normally slopes on my prints look fine, but recently I’ve been getting bad extrusion on some prints but not all. Same materials, same print file. Could this be one of the motors starting to fail? Printed on an ender 3.

Edit: so changing the POM wheels did nothing. However, I did notice while printing the layers weren’t cooling as much as they should before the next layer started. So maybe there could be a fan issue.

93

This guy is my best friend. Dylan. (imgur.com)

submitted 1 year ago by Prismo to c/cat

6 comments fedilink