CadeJohnson

joined 1 year ago
MODERATOR OF
[–] [email protected] 2 points 7 months ago

In the US, stove burners are rated in the confusing units of "BTUs" which is actually a unit of energy, not power. When they say BTU, they mean BTU/hour. The highest-rated burners on a typical stove are about 10,000 Btu (per hour), but high-end stoves can get up to about 18000 - that is equivalent to about 5000 watts. My single-element induction top is only rated for about 1000 watts. So although it heats and cools rapidly, I suspect it is not up to the demands of wok cooking (unless one wants to cook only very small portions).

[–] [email protected] 1 points 7 months ago (2 children)

not Chinese, but I cook a lot with a wok. I also have a single induction cooktop and surprisingly, the wok has enough iron to work with it while some old cheap conventional cookware did not. However, wok cooking needs to be hot all over the wok and not just in that little point where the wok is close enough to the induction coil.

I have a conventional propane stove which I need to keep, because here in Puerto Rico the power system is quite unreliable (especially during a bad hurricane year). But the conventional stove burners are not really hot enough. With a 1/16 - inch drill bit I could increase one of the burners capacity substantially. I painted the stove knob red so people have some warning when they light that burner! It burns more gas, but wok cooking is really fast, so in the long run it is probably more efficient than lots of other cooking approaches.

I would definitely consider a wok-shaped induction heater. Induction heating is quite remarkable.

[–] [email protected] 2 points 7 months ago (1 children)

I'd hate to think modern society is based on a giant elaboration of poker, but I can't rule it out - it MIGHT not be the worst outcome, but a pseudo-equilibrium far from the best. Every young person knows something accessible in the past is now lost to them - not sure what it is, but there is a hole. And yet, the social track laid out is almost unavoidable.

I traveled a good bit the past 20 years and I've experienced first-hand the really hard work and the immense gratification of simple farming. Nobody wants to live like that (at least so they think). Having done it, I can't even say I recommend it over what modern society seems to offer. But since the best option on offer is not a true equilibrium, as the climate is making abundantly clear, what is on offer may be illusory. An alternative equilibrium - tried and true - is worth considering when opportunity arises: subsistence farming. It is NOT simple or easy - don't wait until there is no other option.

[–] [email protected] 4 points 8 months ago (3 children)

I have heard this, and I can imagine it is true, but have you seen any analysis? There must be a large crew traveling and lots of equipment - transportation is a big user of petroleum in general -- for entertainment. Though they say the entertainment is good.

[–] [email protected] 8 points 8 months ago (1 children)

Swimming pools are normally constructed empty. They were withstanding surrounding soil before they were filled, and concrete strength increases with age (for about 90 days, typically). On the other hand, a sunken structure like a pool that is roofed over, becomes a "confined space". Unlike a typical structure, heavier-than-air gases cannot escape from the pool. Such gases could originate from the drain system or flow from leakage outside the pool area. For examples, leaking propane or various gases from sewer lines in the vicinity. A sunken greenhouse would almost certainly be a building code violation for that reason. If you build it, ventilate it by means both active and passive and do not enter if you can't verify that ventilation is working.

[–] [email protected] 2 points 8 months ago (1 children)

the ultimate run-away train! No matter how impossibly big it is, it just grew infinitely bigger in the past second.

[–] [email protected] 3 points 8 months ago

It is not a surprising situation at this point - oil and gas companies already had a large available supply of CO2 from "sweetening" of natural gas. We have to understand the dramatic difference between "capturing" CO2 - meaning capturing from a point source like a stack or process - and "removing" CO2 - meaning removing it from the atmosphere. In normal use, these terms have such similar meanings that it is very easy for nefarious actors to conflate them. It is very easy for regulators to become confused. It is very easy for the oil and gas industry to take advantage of the situation. I think the key solution is education.

The technology to capture CO2 from industrial streams where it is already concentrated, is quite different that removal. Advances in capture technology are only stop-gap and can be better driven by strong enforcement of ever-tighter emission limits than subsidizing of costs.

[–] [email protected] 0 points 8 months ago

maybe space is the graviton field itself(!), but maybe there is a graviton field (or is it the Higgs field?) and gravitons (and Higgs particles?) are excitations of that field; like other particles are excitations of their various postulated quantum fields

[–] [email protected] 2 points 8 months ago (1 children)

I think the most likely route to fast pyrolysis will be as an adjunct to power generation with solar power towers in the midst of heliostat mirrors - just speculation.

I only made a small amount of pyrolysis oil - not enough for any further experiments. I recently have read that it can contain quite an array of fairly toxic benzene-family compounds. It could be refined and "cracked" to make a range of products now made with petroleum, but I just washed mine down the drain into my septic tank (where it will probably remain for some centuries).

[–] [email protected] 2 points 8 months ago

I have plain ol' Ubuntu LTS and I do not recall a Steam crash in a decade. Playing with Nvidia GPU on AMD Ryzen in recent years.

[–] [email protected] 4 points 8 months ago

although this paper is calling for geoengineering via sulfur aerosol in the troposphere, the same logic applies for accelerating CDR

[–] [email protected] 1 points 8 months ago

Right now, there are some CDR methods that absolutely DO make more CO2 than they remove - but that does not mean it has to be that way. The first time you try a recipe, it might not taste so great - you might not even want to eat it at all. But that does not mean the recipe is no good. CDR now is about basic technological development - the processes are creeping up past thousands-of-tons-per-year sort of numbers at commercial scale - but within about 15 years they will need to be at billion ton per year scale (a million times greater). They won't get there burning more carbon than they capture for sure, but they will get there nevertheless (or else . . .)

8
Northern Bishop (slrpnk.net)
submitted 10 months ago* (last edited 10 months ago) by [email protected] to c/[email protected]
 

At Laguna Cartagena, near Cabo Rojo, Puerto Rico (red bird with black chest and mask, perched on green leaves, lit by sunrise)

 

cross-posted from: https://mander.xyz/post/2421501

There seems to be a huge number of miscellaneous projects for a specific type of environmental restoration or some other activity that is specifically aimed at carbon sequestration. For example, seagrass restoration alone has a plethora(1,2,3). Is there a decent list of these projects? I found this cool list of CCS projects(4), but that’s different.

If such a list exists, I have another question: Is there an objective way to compare their effectiveness?

https://www.projectseagrass.org

https://www.medseafoundation.org/index.php/en/portfolio-ita-2/a-sea-forest-to-save-the-planet/34

https://www.seegraswiesen.de/en/

https://en.m.wikipedia.org/wiki/List_of_carbon_capture_and_storage_projects

 

This is a video of my off-grid house in the Dominican Republic, which is featured in this community's title background. It is for sale, so buy it and you can be famous! lolz https://drive.google.com/file/d/16s22L6fgJRtxPQ-a6_aEWy8QJsgsWexN/view?usp=sharing

 

Net Zero is when the bathtub quits overflowing, CDR is how we mop up the water and pump out the flooded basement.

 

These EG4 batteries from Signature Solar look like a pretty good deal to me; $265/kWh according to their calculation. I paid a little over $500/kWh for some 12V form-factor lithium batteries at the start of the year and thought those were a reasonable price.

 

cross-posted from: https://beehaw.org/post/2196737

Like many of you, birds are very special to me. I connect with them like I don’t any other living creature, save my wife and kids. I photograph them. I’ve covered my body in nothing but bird tattoos.

To see that a THIRD of them have disappeared is like a knife to the heart.

 

Today's adventure: a couple of rainy days caused low battery levels, but not too low I thought - still 30% or so; these are lithium batteries and can deep cycle. They are "smart" batteries and if one is full in series, none can charge further - so they should all be at the same charge level all the time. But a couple had gotten out of step somehow and when they reached zero everything shut down.

How to bootstrap it? With no battery output (since a zero battery turned itself off and would not let the battery bank show any voltage!) - there is no way to activate the inverter and let street power run the battery charger. With no battery power, there is no way to turn on the MPPT controller and charge the batteries!

I could rearrange the banks to put four batteries with remaining charge in series because I have an 8-battery system, and get things restarted; but if there had been only four like when I first installed the system - I'd be in trouble.

Another thing that happened. Before I figured out the battery problem, I was trying to switch back to street-power. Because power from the street comes to the inverter first and then the inverter powers the distribution panel, when the batteries are down, I cannot get street power to the distribution panel. I could install a manual bypass, but it is not a commonly needed item and it is a large amp switch. So I removed the inputs and outputs at the inverter and bypassed manually. That worked fine. But in the process of disconnecting or reconnecting, I must have loosened the neutral connection to the inverter. So when the inverter was working again and I checked voltage, I only checked across the two hot legs - yay, 240V. I did not check that each leg was 120v from neutral! They were not: one leg was at zero and the other was at 240. I found this discrepancy fairly quickly after only destroying an outlet strip, the oven control electronics from a very old stove we were wanting to replace, and the controls of an old Sharp microwave oven with the 4, 7, 9 and Clear buttons not working. Woohoo we have a new stove out of the deal!

 

cross-posted from: https://slrpnk.net/post/611077

I have been thinking on how to claim every energy that comes on my plot. Technology goes more and more into harvesting the smaller left over energy. Ive seen examples in the Netherlands where startups try to get energy from a chip (I have been thinking on how to claim every energy that comes on my plot. Technology goes more and more into harvesting the smaller left over energy. Ive seen examples in the Netherlands where startups try to get energy from a chip (http://www.nowi-energy.com, https://memsys.nl) and a transparent solar panel layer on windows etc. Here in Lithuania sometimes the whole day has an overcast sky and that is the solar energy that we are getting. I know that with heavy overcast days a standard solar panels output can be as low as 10%. So a 5kWp can generate instead of 3.75kW produce only a meager 370W. My question to you, arent there other solar technologies that are adjusted to this overcast circumstances? So to gain more efficiency from diffuse lighting or from frequencies that can pierce the clouds more (like infrared spectrum)?

Some sunday morning pondering....

 

The prospects for seaweed to be a key CDR method are still largely unknown. More investigation!

 

cross-posted from: https://lemmy.ml/post/1451658

A new IIASA-led study explored fairness and feasibility in deep mitigation pathways with novel carbon dioxide removal, taking into account institutional capacity to implement mitigation measures.

Meeting the 1.5°C goal of the Paris Agreement will require ambitious climate action this decade. Difficult questions remain as to how warming can be limited within technical realities while respecting the common but differentiated responsibilities and respective capabilities of nations on the way to a sustainable future. Meeting this challenge requires substantial emissions reductions to reach net-zero emissions globally.

Among the new options being studied in scientific literature, engineered Carbon Dioxide Removal (CDR) like Direct Air Capture of CO2 with Carbon Capture and Storage (DACCS), is a potentially promising technology to help bridge this gap. DACCS captures carbon by passing ambient air over chemical solvents, which can be considered a form of CDR if the captured carbon is stored permanently underground. But whether these novel technologies can help make ambitious goals more attainable, or whether they can help reach them more equitably remains an open question.

In their study published in Environmental Research Letters, an interdisciplinary research group led by IIASA scientists developed new scenarios exploring fairness and feasibility in deep mitigation pathways, including novel CDR technologies. For the first time, the team implemented DACCS in a well-established integrated assessment model called MESSAGEix-GLOBIOM, and studied how this technology could impact global mitigation pathways under different scenarios of environmental policy effectiveness based on country-level governance indicators.

"In current policy debates, concerns about the political feasibility and fairness of the current generation of climate mitigation scenarios are raised, and DACCS is often proposed as a possible solution. In our study we quantified under what conditions and how DACCS might address those concerns," explains Elina Brutschin, a study coauthor and researcher in the Transformative Institutional and Social Solutions Research Group of the IIASA Energy, Climate, and Environment Program.

The researchers emphasize that the goal of limiting warming to 1.5°C does not change when considering novel forms of CDR. For a broader perspective on pathways to limit warming, the research team investigated how novel CDR interacts under different assumptions of technoeconomic progress and the evolution of regional institutional capacity. The researchers highlight the risks of dependency on unproven carbon removal while also discussing the role novel CDR and similar technologies could play in the future for developing countries.

The results indicate that novel CDR can keep pre-Paris climate targets within reach when accounting for such risks, but that increasing institutional capacity beyond historical trends is necessary for limiting warming to the Paris Agreement's 1.5°C goal, even with novel CDR processes. The study also suggests that substantially improving institutional capacity to implement environmental policies, regulations, and legislation is critical to keep warming below 2°C if new forms of CDR fail to emerge in the near future.

The authors further point out that, when accounting for the possible future evolution of novel CDR technologies combined with inherent risks, the 'fairness' of overall outcomes did not meaningfully improve. DACCS did not impact near-term required global mitigation ambition, and additional carbon removal in developed economies accounted for only a small component of the mitigation necessary to achieve stringent climate targets. This is because the removal of carbon dioxide in these areas does not compensate sufficiently for their historical emissions by mid-century.

The inability of DACCS to enhance the fairness of outcomes, like cumulative carbon emissions, in 1.5°C scenarios, emphasizes the notion that meeting global climate targets is a global effort requiring an 'all-of-the-above' mitigation strategy. There is no room for flexibility when it comes to reaching climate goals.

The results, however, show that engineered removals can play a role in making the post-peak temperature stabilization (or decline) phase more equitable. This means that the full timeframe under which accounting takes place is critical for exploring fair outcomes that are agreeable by most Parties to the United Nations Framework Convention on Climate Change (UNFCCC).

"Our results show that new technologies for removing carbon from the atmosphere can play a role in ambitious climate policy, but they won't be a silver bullet for solving the climate crisis. Developed countries especially need to cut emissions by more than half this decade, primarily by reducing existing sources of emissions while scaling up CDR technologies to be in line with the Paris Agreement," says study lead author Matthew Gidden, a researcher in the IIASA Energy, Climate, and Environment Program.

The researchers emphasize that there is a clear need for the modeling community to assess the role of novel CDR in a structured way to better understand robust outcomes and insights versus observations related to a given model framework or approach. Looking forward, these issues can be explicitly included in scenario design to arrive at more equitable outcomes while incorporating political realities of the capabilities of governments and institutions to enact strong climate policy.

view more: ‹ prev next ›