this post was submitted on 04 Jul 2023
11 points (100.0% liked)

Nerf

332 readers
1 users here now

Welcome, Nerfers! This is a place for Nerf, Modifications, Homemades, Assassins, Office wars, Humans vs. Zombies, BoomCo, Off-brands, Water Blasters . . .

We're intended to be like /r/nerf except not dependent on reddit.

Are you new to Lemmy? Please click here to expand.

Lemmy is a lot like reddit. For most purposes you can treat it as if it is reddit.

The main difference is that when you view your front page or search for other communities, you have a choice between "subscribed" (what you've already joined), "local" (a small subset of communities) and "all" (every community that this server knows about).

discuss.online is one of many Lemmy servers and many of the communities that you see here originate on other servers - but this networking is handled behind the scenes. This decentralization makes Lemmy resilient but you can still use it just like reddit.

A longer explanation can be found here.


Rules

We have some idiosyncratic rules. Please click to expand and take a minute to read them before posting.

  • Don’t spam (post excessively) or excessively self-promote. That means at most 1 post per day, and less than 1/10ths of your posts and comments each may be self-promotion.

  • No low effort content.

  • Only post thrift finds on Thursday - where "Thursday" starts at 1AM GMT-07 and runs for 24 hours. This corresponds to daylight Thursday for most of our readers.

  • Don’t recommend or show dangerous practices, such as these. There is to be absolutely no deliberate weaponization, even as a joke or against nonhuman targets.

  • Pirated/knockoff versions of hobby-made designs should not be shared; don’t give pirates free advertising.

  • Respect community standards (below) and stay on-topic (further below).

Community standards

We maintain a higher standard of civility here than an average forum. Please be nice, and be forgiving: the other guy might be literally a kid.

We have moderate post quality standards here; nerfchatter is very lax. If you'd like to ask a question, please try googling it first.

It’s “blaster/dart,” not “gun/bullet” - because the latter can lead to things that we'd rather avoid. This is a common mistake, but it is a mistake. Similarly, it's good to be clear that realistic blasters shouldn't be used in public spaces for the benefit of our young readers.

What we aren’t

  • 3d printing questions not specific to nerf should go on 3d printing communities.

  • You can buy/sell/trade/“what’s it worth?” on /r/nerfexchange (though we may make an exchange Lemmy community later).

  • No scripted battle footage. We have to ban this so that we don’t get flooded with it. This is very easy to find on YouTube if you for some reason want to see it.

  • No memes/jokes; there may be rare exceptions for discussions of ongoing events. Again, we have to ban this to not be flooded by it. Memes/jokes are very welcome at Nerfchatter.


Tags

Tagging makes your post easier for people to find.

You can tag a post by including a tag (including the square brackets) anywhere in the title. As a rule of thumb, we suggest that tags higher on this list take priority if more than one could apply.

Resources

[help] - Asking for advice.

[download] - A 3d printable blaster or accessory that's ready to download and print.

[guide] - Writeups (and occasionally videos) describing how to do something.

[review] - Reviews, usually of blasters but also of mod kits etc.

Playing

[event] - An upcoming game looking for players.

[LFG] - Looking For Group.

Showing off

[completed] - A completed project: paintjob, performance mod, integration, etc.

[WIP] - As above except not completed but still something you want to share.

[selfpromotion] - Do you have something to sell? Is this a link to your own YouTube channel? We’d appreciate it if you’re completely upfront about it.

[thrift] - "Hey, look what I just found for cheap in a thrift store!"

[armory] - A picture of your entire collection.

[conceptart] - Concept art for hypothetical blasters, often wit weird and wonderful operating mechanisms.

News

[availability] - Did an anticipated blaster just get released early? Did Amazon accidentally list the DZ Tomcat for a few dollars again?

[1stparty] - For hobby news such as announcements, press releases, and leaks from major manufacturers.

Discussion

[theory] - Ideas, usually on the technical side of the hobby, that you'd like to discuss.

[meta] - Information about this community.


Links

DartSweep: A system for finding games and groups with more features in development.

(old) Map of Active Nerf Groups

3D Printed Blaster Library

Hobby Blaster Catalogue

BritNerf: A traditional forum catering to British foam flingers.

Nerfy Discord Servers: There's tons of Nerf servers on Discord.

Blasted.de: A German forum (and mostly German-language, though English is welcome too).

NerfHaven: A 20+ year archive of information. Not accepting new members.

Interactive Motor Chart

Flywheel Setup Picker

Lipo battery guide, charging, safety tips

founded 1 year ago
MODERATORS
 
you are viewing a single comment's thread
view the rest of the comments
[–] [email protected] 6 points 1 year ago (1 children)

There's a bit of a wall of text incoming here; there's a lot that can be done with a Stryfe. The Stryfe is one of the, if not the, blasters with the most available aftermarket support.

You have a blue Stryfe, which in addition to being the IMHO best-looking Stryfes, came with a dart lock. This lock is intended to lock the trigger when the magazine is empty but can also lock up the trigger while firing rapidly. Removing that lock is the very first thing that I'd recommend doing, if it's not already gone. It's an orange piece of plastic inside of the blaster that sits above the magazine. You can reach in with a screwdriver through the jam door and pop it off.

If you open the blaster, you can remove the magwell lock (prevents the trigger being pulled without a magazine; adds unwanted friction) and perhaps the rev lock (prevents the trigger from being pulled without the rev trigger being pulled first; some people prefer to leave this one in).

After that, I'd recommend a rewire. This requires soldering. (Bodging it without soldering may be tempting but doesn't end well.) 16 or 18 AWG is good; 14 would be overkill and hard to fit into the blaster. You can omit the electronic locks and (puny) overcurrent protection circuit when you rewire - the wire can go straight from your batteries to the rev switch to the motors and back to the batteries.

Replacing the rev switch is a very good idea for reliability. There's plenty of room for an omron v-series switch inside the grip if you cut away some of the existing webbing. To mount the switch, you can glue in place a plastic block with holes for 4-40 machine screws to mount the switch, 3d print one of these, or just hotglue the switch in after soldering.

For batteries, most people would recommend a LiPo pack. If you clean out the battery tray (being careful not to leave any sharp edges) and use a Stryfe extended battery tray cover (there's many designs available to print for yourself or buy on an aftermarket nerf parts store) there should be plenty of room for a pack. Other options include running NiMH rechargeable consumer cells in the stock battery tray for a very mile power upgrade. Beware of AA-sized lithium-ion loose cells - they conveniently fit in a stock tray but are both a fire hazard and a reliability hazard as they can cause battery holder springs to detemper.

If you'd like to take this project further, you can get drop-in replacement upgrade motors, replacement flywheels, and printed flywheel cages with tighter spacing that result in a tighter grip on the dart. (In IMO that order of priority.) Beware that "180" sized motors require cutting the shell to make them fit as they are longer than the normal "130" sized motors; you can buy or print extended motor covers if you go the 180 route.

If you'd like to take the project even further - this is possible, but probably overkill.

Another "upgrade" that you might want to consider is getting aftermarket magazines. I'm personally fond of Worker's 22-round magazines as they offer a good capacity and reliability while being just small enough that I can fit them into tactical gear.

. . . And I haven't even mentioned cosmetic kits. My point is that there's lots and lots of things that you can do.

[–] TwanHE 1 points 1 year ago

Just some add-ons to this in no particular order:

132 size motors will fit if you bend the soldering tabs carefully. The worker half dart kit is quite nice since its compatible with both half and full length darts. Daybreaks / Kepler's are a great option for flywheels (don't get the worker ones imo, I've had some bad experiences with unbalanced wheels from them) If you have a 2s or 3s lipo laying around those are probably the best battery for a higher powered blaster (please do read up on lipo safety)

Lastly find a friend or someone near you that can 3d print parts or get yourself into 3d printing if you're really into the hobby, many sites overcharge for 3d printed components imo.