Ask Electronics

3143 readers

2 users here now

For questions about component-level electronic circuits, tools and equipment.

Rules

1: Be nice.

2: Be on-topic (eg: Electronic, not electrical).

3: No commercial stuff, buying, selling or valuations.

4: Be safe.

founded 1 year ago

MODERATORS

[email protected]

Does multiplexing a usb power cable from 2 cables into 1 impact energy efficiency? (sh.itjust.works)

submitted 8 months ago by [email protected] to c/[email protected]

11 comments fedilink hide all child comments

I have two led strips used for 2x27" monitor bias lighting. Each have their own USB cables for power. These two USB cables are plugged into a 2-port wall charger for a phone. I would like to use a 2x female to 1x male adapter to join the two USB cables into one, then plug it into a much smaller 1-port USB wall charger. The reason is due to my space constraints.

Will doing this impact its energy efficiency, ie using an adapter like this?

https://www.aliexpress.com/item/1005004340044483.html

you are viewing a single comment's thread
view the rest of the comments

[–] [email protected] 1 points 8 months ago (6 children)

There are two questions to answer:

which current and voltage do the LED strips need (5V, 2A would be something you could support with USB 2).
what output does the charger provide as a maximum? Is it enough to power both strips (5V and two times the A).

If these match it should work. Another topic could be the cable itself. Theoretically it could start to burn, if you try to channel to much current through it, but with simple USB I doubt it. If it is getting hot after some time, scrap your setup. This would be a fire hazard.

[–] [email protected] 0 points 8 months ago (3 children)

The LED strips use SMD 3528 LEDs which need 5V and the wattage is listed at 11.52W/min. The amperage isn't listed but for those LEDs, I'm seeing 5Ah online. The charger provides 40W

[–] [email protected] 1 points 8 months ago* (last edited 8 months ago) (1 children)

Watts in a resistive example like yours is Volts x Amps. I would have been able to much better answer this question a year ago so forgive me if I'm misremembering the specs but I'll answer since nobody else has. Two things that suggest to me this might be a bad idea:

Charger is 40W, that's probably usb PD (I don't know anything about QC so maybe I'm wrong). PD supplies more than 15W (5V x 3A) by stepping up the voltage, not the amperage. While stepping up either would likely be bad or very bad for some part of your circuit, don't worry about that though; without the powered device telling it to, PD won't activate. It should max out at 15W... I think. It depends on the resistance on the CC lines and using a splitter could screw up the resistance that tells the power supply which USB version to support so it can go up to 3A (15W). Sorry, it's been a while since I've worked with USB power. 2 strips of 11W will need more power than that. Basically my concern is you won't get adequate power out of the charger for one reason or another.
Where are you getting the 11.52W/min number? Watts don't have a time unit and that much precision sketches me out. Almost as if someone who isn't adequately educated measured the power straight off a multimeter once and just wrote that on a product page. Is the LED strip from a reputable manufacturer?

[–] [email protected] 1 points 8 months ago* (last edited 8 months ago)

He meant watts per meter, not minute – the strips can be cut and rejoined. As for the 5 Ah, no clue.

The circumference of a monitor is more than 1 m, so a charger of 3 A at least will be necessary for each. This is why I prefer higher-voltage strips where less current is required and higher resistance is tolerable. Anyway, the power is quite high and this could cause overheating problems.

load more comments (1 replies)

load more comments (3 replies)