Knives

(Update II) This was 100% a bootleg, and I just got the real one here. The materials feel maybe 1% better, but other than that it's night and day. The blade actually has an edge that will cut paper rather than tear it, though it's not crazy sharp. The blade opens smooth and easy with basically no blade play. There is actually a tip-up clip that carries insanely deep, though I really wish it didn't so I could deploy with a higher position on the handle**. It also isn't insanely over-tight like a lot of the Kershaw wave knives (this made them catch on the pocket, making deployment more difficult). The liner lock actually seats VERY securely, while being easy to manually disengage. The wave feature is actually more aggressive than the bootleg without producing any snagging issues. The sheer length of the blade is more of an issue for deploying than anything else, but even that just a minor gripe imo. Note that there is a chip taken out of the base of the blade, but it looks like this was done to improve liner lock mating.

**After practicing my draw a few more times, the clip depth really is a problem for a knife this size. There just isn't a good way to get the level of purchase I want on the handle, and the bottom really doesn't have enough retention to justify that design choice.

(Update) Turns out this was ~~(probably)~~ a cheap knock-off of an identical and slightly more expensive knife on Amazon. I'm exchanging them and will update on how that does, but won't post a link unless it holds up better.

This is a VERY cheaply built knife, so much so that it's barely worth keeping, let alone carrying. There's not even a pocket clip on it.

BUT, this combination of form and features is EXACTLY what I've been looking for (with a tip-up clip, that is) in a daily carry folder. The handle and finger protection is there, the blade and handle length fit a perfect middle ground for fighting and practicality, it even has a fuckin Emerson style wave that they don't even bother advertising.

Unlike most wave openers, this one is set VERY far back, is slightly oversized, and doesn't have anything forward of it (discs, pegs, etc) to prohibit getting your full blade length.

So if this wasn't so GODDAMN TRASH, I would call it perfect. I haven't seen anything yet, but if there is a brand-name, high(er)-quality knife that is basically this, PLEASE let me know.

Smith & Wesson M&P Border Guard Spring-Assisted Folding Knife

Gerber Sumo Folding Knife

CRKT CEO Flipper Blackout Folding Knife

Buck 264 Cavalier Folding Knife

Gerber Paraframe, Mini Paraframe, and Mullet Keychain Tool Folding Knife Combo

Gerber Paraframe II Knife

I couldn't really argue the point.

Tell me more about this Hammer Brand knife my grandmother gave me. Is it worth anything?

Hi, I've been searching for a Japanese-made Chinese cleaver for a pretty long time and I think I finally found what I'm looking for. I'd really appreciate your thoughts on this, since it's a pretty hefty investment. Link

Thanks in advance!

cross-posted from: https://lemmy.world/post/9035683

And you'll never guess what kind of knife it is. Go on.

...

Yes, of course it's a balisong box cutter. Because it just is.

Update: And the .STL files are released! Get them here, along with assembly instructions, and other sundry bumf.

Okay, so it's not exactly an exciting custom collaboration with a big name manufacturer made out of a supersteel with rich exotic handle materials in a fancy matte box. That would require being considerably more involved with the industry than I am. Which is not at all.

Rather, this is a 3D printable utility/fiddle toy that's ~~ripped off from~~ just a smidge inspired by the Gerber EAB we were talking about the other day. Why doesn't anyone make a flipper like that?

So as our resident balisong expert, I just had to ask myself the other day just how hard developing a working balisong knife could be.

The answer is more than you'd think at first blush. I'm not at all ashamed to report that the production and assembly of one of these takes no less than 26 individual components if you include...

...The optional but fully functional pocket clip.

And yes, it even has a fancy kickerless design with "zen" pins like your big dollar brand name balisong model.

"But does it actually work?" I hear you cry.

You're damn skippy it does.

My design goals were: 1) Make a functional balisong knife that 2) is completely 3D printable without reliance on outside hardware -- other than the blade, obviously -- that 3) plays to the strengths and avoids as much as possible the weaknesses of filament deposition printing and 4) does not require using any supports.

(And yes, you could print the blade, too. If you wanted it to be laughably ineffective.)

Even the assembly hardware is 3D printed, and you can install it using nothing but a penny.

I know you all have been holding your breath until I posted this picture. There you go. You can breathe out now.

Oh, and also: Would you like to use this as a fidget toy that won't get you in too much trouble in polite company, or at the office, or in some backwater hellhole where balisong knives are illegal?

You're in luck. Because there's a blunt trainer blade for it, too.

The Burning Questions I Know You're Going To Ask:

Q: What are the sizes and weights?

42.1 grams. 1.48 ounces. This thing is the second lightest balisong knife I currently own. I designed it in metric, but in keeping with tradition around here it is almost exactly 5" long when closed, 7-1/2" long open (with a typical Stanley style blade installed), 1-1/8" of usable blade edge, and 5/8" of an inch thick (not including the pocket clip, which you can leave off).

Q: That's very funny, but the tolerances on this plastic piece of shit are terrible, right? What does the wiggle test look like, smart guy?

Bam. Stick that in your pipe and smoke it.

Q: But, it's made out of plastic. Isn't it going to break or erode into nothing, like, instantly?

I've been messing around with the above pictured example for about a week now and I've probably flipped it somewhere between six thousand and a zillion times by now. I've been using it to cut up boxes at work all week, too. It's as perfect as the day I minted it.

Q: Isn't cold creep in the PLA going to turn it into a banana eventually?

Maybe! Probably! We're sure as hell going to find out.

Q: Are you going to sell these or something?

I'm not ruling it out, but that wasn't my goal here. I might give a couple away at some point, though.

Q: Then can you shut up and give us the fucking STL files already?

Soon. In order to prevent this post from being longer than it already is, I'm going to release the files and assembly instructions separately. After I'm good and satisfied the design is well tuned enough to inflict upon the unwashed masses, anyway.

I have an 8" chefs knife that I got from...... You know what, I don't remember where. Doesn't matter.

I want some new knives. Mainly a chefs knife, around 8" I guess? Good for slicing bigger cuts of meat and chopping veggi s like carrots, potatoes, broccoli, etc. Also a small knife that makes it easy to cut smaller cuts of meat meat. Is that a paring knife? Is there a 3 or 4" chefs knife? Also, suggestions on a sharpener? I have one of those cheapo pull through ones now. Does OK, but I'm. Sure it could be better

I have many knives that are pretty, elegant, exotic, or otherwise valuable. This... isn't one of them.

The fixed blade I bring camping these days has no make or model; it's an ugly abomination consisting of an eBay D2 blade blank, handle scales I made from a poly cutting board, and a Kydex sheath I knocked together for it. (I do have a belt loop for the sheath as well, but this bastard is a lot to have dangling from your pants, so these days I omit that and either loop it to my pack with that paracord, or just chuck it in my panniers.)

I use it to clear brambles and split firewood, mostly. Yes, I sharpen it with a belt sander. Sometimes it sees a little wire wheel action if I start to get rust spots on it. You have my permission to be suitably horrified.

crosspostato da: https://lemmy.world/post/1378724

Hullo! Could someone help me find a knife with the following:

• small (office duty, max 7cm long)
• Raw Ti scales
• pocket clip
• slip joint or lock with 2-hand opening

The target is to match look and size of a Reylight Pineapple Mini Ti.

Thanks in advance!

I've been EDC a CRKT Minimalist Spearpoint, and my trusty Civivi Elementum. The Spearpoint is new to me and I'm really liking it, very sharp out of the box and small enough that it doesn't come across as "threatening".

What have you got on you?

Why do I have to do a science experiment with lemon juice to know if the knife is stainless steel or carbon steel? Why is it not imprinted on the knife itself so I can verify before purchase? I just want my new knives to not rust after one use. My old knives that I have had for 14 years have not rusted at all. I had to get new ones because water was getting inside the handles of the old ones and would take forever to dry.