this post was submitted on 10 Jul 2023
10 points (91.7% liked)

Woodworking

6222 readers
71 users here now

A handmade home for woodworkers and admirers of woodworkers. Our community icon is submitted by @[email protected] whose father was inspired to start woodworking by Norm and the New Yankee Workshop.

founded 2 years ago
MODERATORS
[email protected]
10
Should I replace all the wooden beams? (lemmy.world)
submitted 1 year ago by umulu to c/[email protected]
13 comments fedilink hide all child comments
 

Hi, I am new here, so I want to apologize if I mess something up. I have the following problem...

I am restoring a division in my house. It's a high ceilling area, with wooden beams supporting a hardwood floor that divides the space into a dining room (lower) and an office (upper).

My father thought the wood was in good shape, so he replaced the hardwood floor above the beams. Afterward, his plan was to apply protection to prevent woodworms and then oil for the finishing touch. But, upon closer inspection, I noticed all the wooden beams have these small holes (which I suppose are woodworms already).

Also, I knocked on the wood, and it seems hollow.

Should I replace all the wooden beams and then reapply the hardwood floor? Is there any way to recover these beams?

Thanks in advance.

top 13 comments
sorted by: hot top controversial new old
[–] [email protected] 5 points 1 year ago (1 children)

To be sure for yourself, you require two experts. 1: Get someone in to do a woodworm survey to check if there is an active infestation. There are a couple of easy checks you can do to make sure a 'specialist' doesn't try to con you. First is to get some paper and tape it to the underside of the wood, leave it a while and if little pellets appear on the paper then there are active woodworm in there. Second is a wood moisture sensor, from what I remember dry wood isn't palatable to woodworm but I could be wrong on that so do some reading. If there aren't any signs then it could have been there for a long time, depending on how old the building is. 2. You've said somewhere else that you'll be putting some stuff above it, if that concerns you then get a structural engineer to take a look at it. They can tell you if it's anything to worry about.

[–] umulu 4 points 1 year ago (1 children)

if that concerns you then get a structural engineer

I did get one, and we decided to replace everything. Thank you

[–] [email protected] 1 points 1 year ago

Sounds like a good decision. Good luck!

[–] [email protected] 3 points 1 year ago (1 children)

Structurally, the beams may be fine (based on the pic you shared). It's also possible that those holes have been there since the beginning.

Are you wanting to recover them aesthetically? Are there any signs of active infestation?

[–] umulu 2 points 1 year ago (1 children)

It’s also possible that those holes have been there since the beginning> I have no way to know because I only purchased the house 2 years ago.

Are you wanting to recover them aesthetically?> I have the money ready if I need to replace them. And I would rather replace than waste time recovering them with wood filler.

Are there any signs of active infestation?> I have not seen any bugs, but I don't know if they are inside.

[–] [email protected] 2 points 1 year ago (1 children)

I would leave them as is, assuming they are exposed beams and I could continue to monitor them. I think worm holes lend to the charm of exposed-wood homes.

I would definitely investigate whether there is an active infestation though, or treat all wood as if there were and then monitor for any developments.

[–] umulu 2 points 1 year ago (1 children)

or treat all wood as if there were and then monitor for any developments

If I did that, would the upper floor have any risk of collapsing? Because the wood seems to be hollow.

[–] [email protected] 4 points 1 year ago (1 children)

Unfortunately, I can't make that call from the one pic, but I would be surprised if that ratio of holes resulted in a hollowed beam. Termites, sure, but not woodworm.

Ultimately, if you won't sleep well with the old wood in place, then there's your answer.

[–] umulu 2 points 1 year ago

Well, I will be putting workbenches with lab power supply, oscilloscope, desktop, monitor, etc... on top of that floor. I would not want to get home one day, and have everything in the dining room from a collapsed floor. But I see what you mean...

[–] Spacebar 2 points 1 year ago (1 children)

Are we looking at the bottom of the wood floor in this picture?

[–] umulu 1 points 1 year ago (1 children)

Yes. You are looking at the beams that hold the upper hardwood floor. What do you think I should do?

[–] Spacebar 2 points 1 year ago (1 children)

Woodworking attacks the outside layer of wood. They dont really eat deep into the piece.

If you don't see any of the worm frass anywhere then that looks to be old worm damage.

Wrap a length of beam in brown paper and wait a few weeks. If there is no worm dust (frass) then I would leave it be.

(The frass is the powdery dust)

If you are still super worried, you could always replace one beam and cut it up to see the inside.

[–] umulu 1 points 1 year ago

That seems like great advice. But since we have already deviced to replace everything, I will just cut the wood and inspect the inside. Maybe I will post an update afterwards. Thank you