So I let the chain wear down too much in the past two years and the rear sprockets appear to be worn out and will need to be replaced. The stock 50T chain ring is also showing signs of wear but appears to still be good for a few years.
I wanted to use this opportunity to see whether I could switch the gearing up a little.
The 13-16 gearing has been surprisingly capable but I need just a little more hill climbing ability; the lowest gear (2.64m) is just barely enough sometimes. I'd like it a tad lower I think.
On the high end, I usually ride in the upper two gears on flat ground. The highest gear (7.98m) feels just a tad too much sometimes though and I then fall back to one lower (6.49m) but that feels a good bit too low. That doesn't bother me a lot but it'd still be nicer to have a gear that's just right.
On a downhill, the highest gear is always sufficient for me; feels pretty much exactly right. I wouldn't mind slightly more metres of development but, honestly, I don't care very much when I'm already going way past 30km/h and I don't ride downhill for very long usually. I'm unsure whether reducing the highest gear slightly would make me pedal uncomfortably quickly down hill though.
Stock and current config:
| Hub | 64% | 100% | 157% |
|---|---|---|---|
| Low sprocket | 2.64 | 4.14 | 6.49 |
| High sprocket | 3.25 | 5.10 | 7.98 |
I'm currently thinking about a 44T chain ring with 12-17:
| Hub | 64% | 100% | 157% |
|---|---|---|---|
| Low sprocket | 2.19 | 3.43 | 5.37 |
| High sprocket | 3.10 | 4.86 | 7.61 |
or 12-16:
| Hub | 64% | 100% | 157% |
|---|---|---|---|
| Low sprocket | 2.33 | 3.64 | 5.71 |
| High sprocket | 3.10 | 4.86 | 7.61 |
The lower gears being lower and closer together sounds very nice.
In the higher gears, my hope is that the slightly lower highest gear would allow me to use it the majority of the time on flat ground because I suspect the second highest gear would feel quite a bit too low as a fall-back.
I could see 12-15 being an option perhaps but that also gets the lowest gear much closer to 13-16 again:
| Hub | 64% | 100% | 157% |
|---|---|---|---|
| Low sprocket | 2.48 | 3.89 | 6.09 |
| High sprocket | 3.10 | 4.86 | 7.61 |
But obviously the lowest gear gets very close to the previous config again.
Where I have a hard time is imagining how significant the difference between 2.64m, 2.19m, 2.33m and 2.48m are in an uphill scenario. The jump between the lower gears in 13-16 (3.25m to 2.64m) in practice feels significant but not that large either and we're talking about a much lower absolute drop being gained in the low end by switching gearing. I don't know whether the practical effect of this is linear though and I suspect it might not be.
I'd really appreciate practical experience here. Have you changed gearing on your Brompton? From what to what and how significant were the differences?
You appear to be misunderstanding. This isn't about making gearing be closer together, this is about increasing the range of the gearing by making the low end lower and only reducing the high end by a little.
If anything, the configurations I wrote about would make gear spacing less even as the default is quite nicely spaced.
What I need to know is whether the change in the low end is actually noticeable in an uphill scenario and by how much.
It's the same for me I think. I'd prefer some variety of low gears for uphills and some variety for relatively flat ground. I don't very much care what's in between as long as it's not too far apart.
When I start riding, I usually use one of the lower gears for half a turn and then immediately switch the hub from 64% to 100% (skipping the gear in between) which is a jump from 2.64m to 4.14m or 3.25m to 5.10m and then usually up to 5th gear (6.49m) for a bit and then the 6th gear when conditions allow.
This again appears to be a misunderstanding: This is a 6-speed Brompton.
6-speed here means 6 gears total, including the hub.
The gearing is as follows:
I get to choose the two sprockets and the chainring. That's it; there is no wider cassette that physically fits this frame.
The reason for changing the chainring is merely to shift the gearing down which isn't possible by changing the sprockets because a sprocket larger than about 17T will physically not fit. Again, this is a Brompton with tiny 16" wheels that folds down to suitcase size.