this post was submitted on 11 Jul 2023
5 points (100.0% liked)
Fountain Pens
367 readers
8 users here now
Inspired by /r/fountainpens, a place to discuss pens, writing, ink, paper, and whatever else makes your pen flourish.
Related
Banner: @[email protected] (Nakaya Decapod) | Icon: @[email protected]
founded 1 year ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
I've not known a converter causing issues such as drying out. I'm a bit confused about how you are fixing it? Do you mean you screw the converter a little to lower the piston and that gets it going again? That is a common fix for a dried up pen.
Have you tried different inks? It might be the ink is just not compatible with the pen.
As already mentioned you can get converters (Faber Castell makes one) with agitators in them to help prevent the ink from staying at the wrong end of the converter but most of the converters I own are fine without them.
I would try getting a sample of a well known reliable ink such as Waterman Serenity Blue and seeing if the pen behaves well using it. Also try flushing your pen with some mild soapy water or pen flush, maybe even allowing it to soak for a few hours. You may have dried up ink or some oils from manufacturing in the feed that are impeding flow.
Sometimes it is just a problem with the pen/cap design due to a poor seal. I had a wooden Conklin All American Golden Walnut and it would stop writing if left for more than a few hours. The cap had no liner in it and the raw wood just sucked all the moisture from the nib and dried it out. Ultimately despite liking the pen I just sold it due to frustration.
Yes, that's what I am doing. I had no trouble with the cartridge I used before, so I could try that again to identify the converter as the issue. The ink is Parker Quink Black (but two decades old, so possibly alcohol-based? I read something about a change in formula). It is supposed to be one of the more reliable ones.
If I don't have problem with a cartridge, then I can exclude the cap as the source of the problem, right?
As a follow up to warped, do you have the old cartridge and a blunt syringe? I can't tell if you tested with an unused or refilled cartridge. I will run with the assumption you only tested with an unused one. You can test if this is an ink compability or an evaporation issue by filling the old cartridge with the Quink. No need to fill it completely and waste ink. 1/4 should be enough to tell. Use the pen as you did with the converter and see if you have the same evaporation issues. If it's also evaporating, it is either a cap seal issue or a pen and ink combo. I second Warped's recommendation to try the ever reliable Waterman Serenity Blue (the "standard" blue shade") ink. That will give you a good idea if your pen has an evaporation issue (still drying out quickly) or a pen/ink combo issue. If there is no evaporation (no dry out and ink isn't getting darker), then you can start branching out to different inks to figure out what works with the pen. If you do not have any issue with the refilled with Quink cartridge, then I think that might suggest a converter related issue. The agitator might help. A new converter might help too. This scenario is a bit harder to diagnose to be honest.
If I was a gambler, I would bet it's either an evaporation or pen/ink combo issue.
If a cartridge behaves fine then the cap seal is less likely to be the problem, but again different inks behave in different way that may accentuate a cap seal problem. Very few pen caps create perfect seal anyway but some are better than others (I think Platinum have the Slip and Seal system).
If your ink is alcohol-based (never heard of this but then I don't have any old ink) then I would imagine it would be highly susceptible to evaporation and drying out. I'd pick up some different water-based ink if you prefer the CC over cartridges.